FlexRadio Systems FLEX-5000A Скачать руководство пользователя страница 11

Страница: 11 / 11

Verify that PowerSDR Recognizes the N ewly Installed ATU

a. Start PowerSDR.

b. Select the “Setup” tab in the upper left of the PowerSDR screen.

c. Select the “General” tab.

d. In the “Config” section, make sure ‘ATU’ is present and shows the proper serial number and revision 52B (or
higher) in parentheses. If not displayed, then submit a support ticket via our HelpDesk
(

http://helpdesk.flexradio.com

) so we can assign you a case number and resolve the installation issue. For details

on how to submit a HelpDesk support ticket, please refer to the following URL:

http://support.flexradio.com/

. An

improperly installed ATU can damage your radio which will not be covered under warranty repair.

Operation of the FLEX-5000 ATU

a. Refer to the FLEX-5000 User’s Manual for instructions on the operation of the ATU using PowerSDR.

Содержание FLEX-5000A











Результаты поиска

Содержание FLEX-5000A

Отзывы:

Похожие инструкции для FLEX-5000A

Бренды по названию

Популярные бренды

FlexRadio Systems FLEX-5000A, Руководство по установке

Результаты поиска

Содержание FLEX-5000A

Отзывы:

Похожие инструкции для FLEX-5000A

Бренды по названию

Популярные бренды