Flexim FLUXUS G801 Скачать руководство пользователя страница 146

Страница: 146 / 177

17 SuperUser mode
17.2 Transducer parameters

FLUXUS G801

2020-06-26, UMFLUXUS_G801V1-0EN

146

17.2

Transducer parameters

In the SuperUser mode, the menu item

Transducer Type

will be displayed in the program branch

Parameter

at the

end of the input even if the transducers are detected by the transmitter.

• Press ENTER.
or:

• Select

Special Version

to enter the transducer parameters.

• Press ENTER.

• If

Special Version

is selected, the transducer parameters have to be entered.

The transducer parameters have to be provided by FLEXIM.
• Press ENTER after each input.

17.3

Definition of the flow parameters

In the SuperUser mode, it is possible to define some flow parameters (profile bounds, correction of the flow velocity) for

the specific application or measuring point.

• Select the menu item

Calibrat. data

• Press ENTER.

• Select the measuring channel for which the flow parameters are to be defined (here:

Channel A

• Press ENTER.

17.3.1

Profile bounds

• Select

user

to define the profile bounds. If

factory

is selected, the default profile bounds will be used and the menu

item

Calibration

will be displayed.

• Press ENTER.

• Enter the max. Reynolds number at which the flow is laminar. The entered number will be rounded to hundreds.

Enter zero to use the default value of 1000.

• Press ENTER.

• Enter the min. Reynolds number at which the flow is turbulent. The entered number will be rounded to hundreds.

Enter zero to use the default value of 3000.

• Press ENTER.

Parameter\...\Transducer Type\Q2E-314

Parameter\...\Transducer Type\Special Version

Parameter\...\Transducer Type\Special Version\Transd. Data 1

Special Funct.\SYSTEM settings\Measuring\Calibrat. data

Special Funct.\SYSTEM settings\Measuring\Calibrat. data\for Channel A

Special Funct.\...\Calibration\...\Profile bounds

Special Funct.\...\Calibration\...\Laminar flow

Special Funct.\...\Calibration\...\Turbulent flow

Содержание FLUXUS G801


















































































































































































Результаты поиска

Содержание FLUXUS G801

Отзывы:

Похожие инструкции для FLUXUS G801

Бренды по названию

Популярные бренды

Flexim FLUXUS G801, Руководство по эксплуатации

Результаты поиска

Содержание FLUXUS G801

Отзывы:

Похожие инструкции для FLUXUS G801

Бренды по названию

Популярные бренды