1/26/2021
REV. 007
51
TROUBLESHOOTING
Refer to the following list of common problems when it appears the FlexArm is not working properly. Most of
these are resolvable by in-house technicians or operators. Compare any problems with those given in the
examples below. Help is just a phone call away; always contact Factory Service at
800-837-2503
with any
questions or concerns about the
FlexArm Tapping Machine.
●
The tap is not maintaining perpendicularity
o
Check to make sure the angle mount bolt or bolts are tight.
o
Check the flatness of the surface on which the unit is mounted.
o
Check the motor mount screws. Make sure they are tight and are holding the motor securely in the
mount.
o
Check the hole being tapped. If the hole is not perpendicular to the surface where the unit is
mounted, the hole will not be straight.
o
Check the run out of the chuck. The chuck and spindle may have been damaged.
o
Check the part fixture. If the fixture isn't holding the part level or true, the tapped hole will not be
straight.
o
Check the tap and the tap holder. The tap or the holder may be worn and need repair or
replacement.
o
Also, check that the tap is secure in the holder and held tightly.
o
Check both the bottom and top surfaces of the base mount and angle mount for excessive wear,
nicks, dings, etc., anything that would prevent the unit from sitting level to the mounting surface.
●
The unit does not have enough power to drive the tap
o
Check the inverter inside of the electrical cabinet for an error code. If there is an error, contact
Factory Service at
800-837-2503
to talk to a service technician.
o
Check the condition of the tap being used and try a new tap to verify whether the old one is worn
out.
o
Check that both the lubricant and the amount of lubricant are adequate for the material being
worked.
o
If using a torque style tap holder, it may be necessary to adjust the holder up a notch (See adjusting
the tap holder settings in the manual pg. 20)
o
Check the power pack for proper oil level using the sight gauge on the power pack's front. Verify that
the oil and filter have been changed in accordance with the maintenance section of the manual.
Содержание GH-24
