Flex PXE 80 10.8-EC Скачать руководство пользователя страница 10

PXE 80 10.8-EC

11

 

■ Do not use a damaged accessory. Before 

each use inspect the accessory such as 

abrasive wheels for chips and cracks, 

backing pad for cracks, tear or excess 

wear, wire brush for loose or cracked wires. 

If power tool or accessory is dropped, 

inspect for damage or install an undamaged 

accessory. After inspecting and installing an 

accessory, position yourself and bystanders 

away from the plane of the rotating accessory 

and run the power tool at maximum no-load 

speed for one minute. Damaged accessories 

will normally break apart during this test time.

 

■ Wear personal protective equipment. 

Depending on application, use face 

shield, safety goggles or safety glasses. 

As appropriate, wear dust mask, hearing 

protectors, gloves and shop apron capable 

of stopping small abrasive or workpiece 

fragments.The eye protection must be capable 

of stopping flying debris generated by various 

operations. The dust mask or respirator must 

be capable of filtrating particles generated by 

your operation. Prolonged exposure to high 

intensity noise may cause hearing loss.

 

■ Keep bystanders a safe distance away from 

work area. Anyone entering the work area 

must wear personal protective equipment. 

Fragments of workpiece or of a broken 

accessory may fly away and cause injury 

beyond immediate area of operation.

 

■ Never lay the power tool down until the 

accessory has come to a complete stop. The 

spinning accessory may grab the surface and 

pull the power tool out of your control.

 

■ Do not run the power tool while carrying it at 

your side. Accidental contact with the spinning 

accessory could snag your clothing, pulling the 

accessory into your body.

 

■ Regularly clean the power tool’s air vents. 

The motor’s fan will draw the dust inside 

the housing and excessive accumulation of 

powdered metal may cause electrical hazards.

 

■ Do not operate the power tool near flam- 

mable materials. Sparks could ignite these 

materials.

 

■ Do not use accessories that require liquid 

coolants. Using water or other liquid coolants 

may result in electrocution or shock.

Kickback and Related Warnings:

Kickback is a sudden reaction to a pinched or 

snagged rotating wheel, backing pad, brush 

or any other accessory. Pinching or snagging 

causes rapid stalling of the rotating accessory 

which in turn causes the uncontrolled power 

tool to be forced in the direction opposite of the 

accessory’s rotation at the point of the binding. 

For example, if an abrasive wheel is snagged or 

pinched by the workpiece, the edge of the wheel 

that is entering into the pinch point can dig into 

the surface of the material causing the wheel to 

climb out or kick out. The wheel may either jump 

toward or away from the operator, depending on 

direction of the wheel’s movement at the point of 

pinching. Abrasive wheels may also break under 

these conditions. Kickback is the result of power 

tool misuse and/or incorrect operating procedures 

or conditions and can be avoided by taking 

proper precautions as given below.

 

■ Maintain a firm grip on the power tool and 

position your body and arm to allow you to 

resist kickback forces. Always use auxiliary 

handle, if provided, for maximum control over 

kickback or torque reaction during start-up. 

The operator can control torque reactions or 

kickback forces, if proper precautions are taken.

 

■ Never place your hand near the rotating 

accessory. Accessory may kickback over 

your hand.

 

■ Do not position your body in the area where 

power tool will move if kickback occurs. 

Kickback will propel the tool in direction 

opposite to the wheel’s movement at the 

point of snagging.

 

■ Use special care when working corners, 

sharp edges etc. Avoid bouncing and 

snagging the accessory. Corners, sharp 

edges or bouncing have a tendency to snag 

the rotating accessory and cause loss of 

control or kickback.

Safety Warnings Specific for 

Polishing Operations:

 

■ Do not allow any loose portion of the 

polishing bonnet or its attachment strings 

to spin freely. Tuck away or trim any loose 

attachment strings. Loose and spinning 

attachment strings can entangle your fingers 

or snag on the workpiece.

Содержание PXE 80 10.8-EC















Отзывы: