manualshive.com logo in svg

Flex innovations FV-31 Cypher, Инструкция по эксплуатации

Поделиться
Скачать
Flex innovations FV-31 Cypher Скачать руководство пользователя страница 35

Nose Gear

Nose Gear

FLIGHT CONTROL SENSING DIRECTION TEST

Aircraft

Movement

Proper Control

Surface Deflection

AILE

RON

ELEV

A

T

OR

RUDDE

R

Perform a test of the gyro system to verify the corrections made for a given movement are correct. If any of the tests do not result in the 

correct reaction for the airplane's gyro system, 

DO NOT FLY THE AIRCRAFT

, and contact us via email at [email protected].

The flight control system activates with RF broadcast. Perform these tests in the Beginner Profile (6-axis) for better visibility, and then again 

in the Advanced Profile. Please note that the control surfaces will 

ALWAYS

 try to correct the aircraft to level in the Beginner Profile but will 

ONLY

 correct while the aircraft is 

ROTATING

 in the Advanced Profile.

Yaw correction is done with the motors and will only be active when the aircraft is armed. Either two or four motors may activate 

depending on the Flight Configuration selected and throttle position. 

33

Содержание FV-31 Cypher



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды