FLENDER K.A Series Скачать руководство пользователя | Manualshive

Страница: 77 / 128

background image

5.7.9

Connecting the heating element

Procedure

To connect heating elements to the gear unit, proceed as follows:
1. Check that the heating element connection is not damaged.
2. Install the electrical wiring for the heating elements.

Further information

Further information about the heating can be found in the heating operating instructions in the

complete documentation for the gear unit.

5.7.10

Connecting the bearing monitoring system

Procedure

To connect the Pt 100 resistance thermometer, proceed as follows:
1. Check that the Pt 100 resistance thermometer connection is not damaged.
2. Install the electrical wiring between the Pt 100 resistance thermometer and the evaluation

unit. The customer is responsible for providing the evaluation unit.

Further information

Further information about the Pt 100 resistance thermometer can be found in the Pt 100

resistance thermometer operating instructions in the complete documentation for the gear unit.

5.8

Tightening procedure

5.8.1

Introduction

Bolts

The bolts must have the following properties:
● Made of steel
● Black-annealed or phosphatised
● Lightly oiled (do not add additional oil)

Mounting

5.8 Tightening procedure

REDUREX Gear unit 5200en

Operating Instructions 03/2019

77

«
...
75
76
77
78
79
...
»

Содержание K.A Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для K.A Series

Ettan IPGphor 3

Бренд: GE Страницы: 64

Бренд: GE Страницы: 56

Бренд: GE Страницы: 132

Бренд: GE Страницы: 16

Бренд: GE Страницы: 474

Бренд: Rain-Flo Irrigation Страницы: 20

Attest Auto-reader 390

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Dynapro ET 355 Monitor HL

Бренд: 3M Страницы: 23

PELTOR WS LiteCom Plus

Бренд: 3M Страницы: 7

Steri-Vac GS Series

Бренд: 3M Страницы: 52

Бренд: XanLite Страницы: 4

Бренд: Hammer Страницы: 42

Бренд: PASCO Страницы: 30

Бренд: Qlight Страницы: 3

Бренд: qtran Страницы: 2

Бренд: Q-Optics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды