FLENDER K.A Series страница 64 Скачать руководство пользователя | Manualshive

Страница: 64 / 128

background image

5.4.1

Mounting

Measures to be taken prior to assembly

CAUTION

Risk of injury due to chemical substances
Observe the manufacturer’s guidelines on how to handle lubricants and solvents.
Wear suitable protective clothing.

Improper use can damage the gear unit. Be sure to take the following precautions:
● Use a suitable cleaning agent to remove the corrosion protection from the hollow shaft and

the machine shaft.

● Inspect the hollow and machine shafts for damaged seats and edges.
● If necessary, rework the components with an appropriate tool and then clean them again.
● Apply an appropriate lubricant to the contact surfaces to protect them against fretting

corrosion.

NOTICE
Risk of damage to shaft sealing rings from cleaning agent
Aggressive chemical cleaning agents may cause damage to shaft sealing rings.
Do not allow the cleaning agent to come into contact with the shaft-sealing rings.

5.4.1.1

Mounting

Procedure

NOTICE
Damage to the gear unit
The gear unit can become damaged if it skews during assembly.
The hollow shaft must be flush with the machine shaft during assembly of the gear unit on the

machine shaft. The gear unit must be prevented from skewing.

Mounting
5.4 Shaft-mounted gear unit with hollow shaft and parallel keyway

REDUREX Gear unit 5200en

64

Operating Instructions 03/2019

«
...
62
63
64
65
66
...
»

Содержание K.A Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для K.A Series

Бренд: Hanil Страницы: 60

Бренд: Tabi Страницы: 8

Бренд: Dabi Atlante Страницы: 102

Бренд: Quivogne Страницы: 13

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: O2matic Страницы: 4

Бренд: Saadat Страницы: 61

Бренд: Saadat Страницы: 22

Бренд: VADDIO Страницы: 58

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Reformer Trapeze Combination

Бренд: Balanced Body Страницы: 164

Бренд: Wacker Neuson Страницы: 50

Бренд: Balanced Body Страницы: 37

Бренд: Varimixer Страницы: 28

Tacx Boost Bundle

Бренд: Garmin Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды