FLENDER K.A Series страница 54 Скачать руководство пользователя | Manualshive

Страница: 54 / 128

background image

NOTICE
Lack of stable foundation for the gear unit
Damage to the gear unit is possible if it is not mounted on a stable foundation.
Use bolts of at least strength class 8.8. Information and guidance on the tightening torque can

be found in chapter Tightening procedure (Page 77). Tighten the fastening bolts and nuts to

the specified tightening torque. When tightening the fastening bolts, make sure that the gear

unit is free of mechanical stress.

Further information

Further information about dimensions, space requirements and arrangement of supply

connections can be found in the complete documentation for the gear unit.

5.3.2

Fastening

5.3.2.1

Mounting on a housing foot

Description of the mounting work

Measures to be taken prior to assembly

CAUTION

Risk of chemical burns due to chemical substances
There is a risk of chemical burns when handling aggressive cleaning agents.
Please observe the manufacturer's guidelines on how to handle cleaning agents and solvents.

Wear suitable protective equipment (gloves, safety goggles). Please use binding agents to

immediately clear up any spilt solvent.

WARNING

Risk of burns
There is a risk of serious burn injury from hot surfaces (> 55 °C).
Wear suitable protective gloves and protective clothing.

Improper use can damage the gear unit. Be sure to take the following precautions:
● Use a suitable cleaning agent to remove the corrosion protection from the shafts.
● Do not allow the cleaning agent to come into contact with the shaft-sealing rings.

Mounting
5.3 Gear unit mounting

REDUREX Gear unit 5200en

54

Operating Instructions 03/2019

«
...
52
53
54
55
56
...
»

Содержание K.A Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для K.A Series

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: iGuzzini Страницы: 20

PowerXL DX-NET-ETHERNET2-2

Бренд: Eaton Страницы: 48

Power Xpert C445

Бренд: Eaton Страницы: 2

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: Madsen Страницы: 206

Бренд: Quincy Страницы: 31

Lyme FIA Sofia 2

Бренд: Quidel Страницы: 49

Бренд: Quest Leisure Products Страницы: 12

Бренд: UNIS Страницы: 16

Bathomatic Basic

Бренд: Unique Automation Страницы: 10

Бренд: Additel Страницы: 139

Бренд: Garmin Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды