Flavel RENOIR RC Скачать руководство пользователя страница 17

Страница: 17 / 54

3.3

LIGHTING THE FIRE MANUALLY VIA THE CONTROL VALVE

3.3.1

These products can be operated manually by using the buttons directly

on the fire control in addition to the handset (should the need arise).

3.3.2

To operate the fire press and hold the “power” button as shown below

in figure 14 for two seconds, release as soon as the red indicator light

shown in figure 14 illuminates. The burner will then start its

ignition sequence and light to the maximum heat input level.

For most

efficient performance leave the fire on high when lighting from

cold for ten minutes.

Fig. 14

3.3.3

To reduce the heat input, press and release the (-) button to lower the

heat input level one step at a time. Pressing the (-) button continuously

will move the heat input level to the minimum.

3.3.4

To increase the heat input level, press then release the (+) button to

increase the heat input level one step at a time. Pressing the (+) button

continuously will move the heat input level to the maximum.

3.3.5

To turn the fire off, press the power button and the burner will stop.

3.3.6

Indicator light

Power isolation switch

Battery compartment

cover opening lever

Battery

compartment

cover

Power button

Increase flame

Decrease

flame

If you are not intending to use the fire for a long period (i.e.

over the summer months) the battery life can be extended by

sliding the power isolator switch to the left (to the “0” position

away from the “1” position) on the valve itself, which is located

behind the ashpan cover on the fire.

Содержание RENOIR RC























































Результаты поиска

Содержание RENOIR RC

Отзывы:

Похожие инструкции для RENOIR RC

Бренды по названию

Популярные бренды

Flavel RENOIR RC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание RENOIR RC

Отзывы:

Похожие инструкции для RENOIR RC

Бренды по названию

Популярные бренды