Flavel Calibre FBFC**MN2 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 38

Flavel Calibre FBFC**MN2 Скачать руководство пользователя страница 22

3.7

LIGHTING THE APPLIANCE - REMOTE CONTROL MODELS ONLY

3.7.1

The Remote control handset generates an infrared signal, which will be

received by the sensor situated at the front right of your fire, behind the

ashpan cover. This infrared signal requires direct line of sight from the

handset to the sensor on the fire to ensure good operation.

3.7.2

To light the appliance using the handset, point the handset at the fire

and press the 2 left hand buttons together as shown below in Fig. 20

The fire will emit a “beep” sound, the buttons can now be released. After

a few seconds an audible clicking can be heard and then the fire will

light the pilot and then light the main burner. The ignition cycle will take

approximately 20 seconds.

3.7.3

To reduce the level of heat input on the fire, point the handset at the fire

and press the small flame button. (An audible beep will be heard)

3.7.4

To increase the level of heat input on the fire, point the handset at the

fire and press the large flame button. (An audible beep will be heard)

3.7.5

To leave the fire in the standby mode (pilot only running) press the small

round button on the handset.

3.7.6

To switch the appliance off completely, press the large round button on

the handset, the fire will then switch off.

Fig. 20

WHEN TURNING THE FIRE “OFF” PLEASE ENSURE THAT THE PILOT

FLAME IS EXTINGUISHED. DO NOT LEAVE THE PILOT FLAME ONLY LIT.

22

Off Button

High (Large Flame)

Low (Small Flame)

Standby Button

«
...
20
21
22
23
24
...
»

Содержание Calibre FBFC**MN2







































Отзывы:

Нет отзывов