Operating the Fire
Areas around the fire will become hot when activated. We strongly recommend small children be kept away from having any direct
contact with the appliance by means of fitting a fireguard. This appliance is not intended for use by persons (or children) with
reduced physical sensory or mental capabilities or lack of experience or knowledge unless they have been given supervision or
instruction concerning the use of the appliance by the person responsible for their safety. Children should be supervised to ensure
they do not play with this appliance.
Fire Controls (Manual can be found under the opening)
The
main on/off switch
is marked with
I/O
and will need to be switched to
I
to operate the fire. In this position you will be
unable to operate the fire further unless the
button on the remote or keypad is pressed first.
To operate the flame effect (and further functions) simply press and release the
button on the remote or keypad.
To set the flame effect to your desired brightness press then release
+
or
-
buttons marked either side of the
icon.
The heater will always start in the lower setting.
For 1KW of heat, press then release the button marked
O/I.
To
increase the temperature to 2KW press then release button marked
I/II
. You may alternate from 1KW to 2KW by
pressing
I/II
at anytime. To turn the heater off, press then release the button marked
O/I.
To turn the flame effect off and deactivate the heater and dimmer functions press then release the button marked
.
Recommended
To turn the fire off completely the
main on/off switch
must be switch back to
O.
Automatic safety cut out
The heater is fitted with an automatic cut out to prevent any damage due to overheating. The element will continually and
automatically cut out if the airflow is obstructed.
Never
cover the air inlets or outlets. To reset the fire, switch the fire off, disconnect
from the mains supply, remove the cause of overheating and allowed to cool for a suitable period then switch the fire back on.
Caution:
In order to avoid a hazard due to inadvertent resetting of the thermal cut out, the appliance must not be supplied through an
external switching device, such as a timer, or connected to circuit regularly switched on and off by a utility.
Maintenance
Before any maintenance/cleaning is undertaken always disconnect the fire from the mains power supply.
Replacing Lamps (Dimmable 240V 5W 3000k E14 LED lamps): Replacements are available from Flamerite Fires
Please note that replacement Lamps are only covered by a 2 year warranty from purchase. Allow a suitable time for the lamps to cool then
remove the pebbles/coals fuel effect. The fuel bed may be lifted out of place. Unscrew and replace the lamps.
Changing or matching remote frequency
If you receive a replacement remote in case of loss/damage or your remote interferers with another appliance near by you are able to change
to an alternative frequency/address by following a simple procedure.
1. Make sure the fire is turned to standby (off, but not from the mains) and the LED on the
manual keypad
is lit.
2. On the
manual keypad
press and hold the heater on & heater Hi/Low buttons together for 5 seconds and the LED will flash.
3. Press the
FIRE ON or
button on the
remote control
. The fire will turn on & off twice.
The procedure is now complete and the fire is once again ready for use. (
If no illumination turn off main on/off switch
and leave for one
minute to reset software).
Changing battery in the remote
Your remote uses a CR2032 Lithium Battery, replacements are available from Flamerite Fires and its stockists (see top of page 1). Ensure
battery is disposed of safely. Do not dispose of in fire, do not swallow and keep away from children.
Cleaning
The fire can be cleaned with a damp cloth and non abrasive cleaner.
Warnings
Do not use the fire in the vicinity of a bath shower or swimming pool.
Never use the fire to dry laundry.
Never install the fire directly underneath a fixed main socket.
Never cover the appliance during the operation of the fire.
The use of an extension lead is not recommended.
Particular caution should be applied to ensure that children do not play with the pebbles/coal.
As with any electrical appliance whilst the instructions aim to cover as many eventualities as possible, caution and common sense
should be applied when operating your appliance, particularly in the vicinity of small children.
Problem solving
No power to the fire:
Check the wall socket, plug and fuse.
No illumination:
Make sure the fire is turned on. Check heater is working, if so change lamps.
Illumination but no heat:
The safety cut has operated see note on operating the Fire.
Noise when illuminated:
Due to moving parts, the electric fire will make a noise.
Noise from the heater when in use:
The sound of rushing air is normal.
