INSTRUCTIONS FOR USE
Corello/Yukon
Remove the fire from the packing, checking that neither the heater nor the power cable has been damaged during transport. Do not operate
the heater if damaged. The accessories are found in a box that is packed at the side of the fire. Your fire is guaranteed for one year from the
date of purchase. In the unlikely event of a breakdown you have access to our customer services team, simply call
01543 251122
during office
hours, 9am – 5pm or e-mail on
INSTALLATION OF THE FIRE
Before any maintenance is undertaken always disconnect the fire from the mains power supply.
The inset dimensions for Hole in the Wall: depth 12.5cm, height 55cm and width 54cm. To prevent the fire from being pulled over it must be
secured into place. The height at which you wish to fix the fire to the wall is up to you, though we recommend 60cm from the floor to the
bottom of the fire.
Using as a Hole in the Wall:
THE SPACER MUST BE REMOVED (FIG.2)
Fig.1
Fig.2
Where a chimney is not blocked off completely it will cause the heater to cut out during use. If you are not sure that you have cut off the
draw 100% from the chimney, we recommend covering the five banks of slots in the rear of the case (Fig.2) and each bank either side.
Removing the decorative front (
Fig.1
), there are two screws either side of the heater outlet next to the on/off switch and the keypad and two
inside the fire under the fuel bed area beneath the lamps (
B
). To remove the spacer there are eight screws (
A
) on the rear of the case (
Fig.2
).
Four keyhole slots should now be visible, two on each side of the outer return. Place the fire into the hole, mark off at the
TOP
of the keyhole
slots
where the fixing holes are to be drilled. Remove fire and drill the holes. When this is done push the rawl plugs into the drilled holes and
half screw in the fixings. Finally lift and hook the fire back onto the fixings and tighten. The decorative front may be reapplied.
Using as a Hang on the Wall.
The rail should be fixed to the wall with the
hook
facing upward and outward. Once the rail has been fixed in
place, lift and hook the fire onto the rail. Next at the back of the case bottom/centre is a fold out tag. Fold this down as to expose it under the
fire when it is hung in place. Mark off through the hole, remove fire, drill and fit rawl plug. Hang the fire back on the wall and secure in place
using the screw provide.
Important: The fire must be positioned so that the plug socket is accessible once the fire has been installed. In the unlikely event of
breakdown access must be allowed for so that the fire maybe serviced (DO NOT SEAL). This will involve the fire being removed from the
wall in order to gain access the rear. The mains cable must therefore be long enough to allow this. If the removal of the plug is absolutely
necessary for installation, cut off in an area within 100mm only of the plug itself. Any further will affect your warranty. Where an inset fire
is being used in an existing chimney, it is important that the chimney is blocked off to prevent airflow problems with the fire.
Electrical connections
Your appliance comes fitted with a plug that incorporates a 13A fuse. The replacement fuses must be 13A and ASTA approved. If the fuse cover is lost the plug
must not be used until a replacement cover, of the same colour, is obtained from an electrical retailer.
The appliance is fitted with a moulded plug if it is necessary cut off the plug, for any reason, it must be discarded immediately with the fuse removed.
Under no circumstances should any attempt be made to reuse the plug, do not insert into any 13A socket as this could cause a hazard. If the mains
cable is damaged it must be replaced by the manufacturer or an authorised technical service centre.
WARNING THIS APPLIANCE MUST BE EARTHED
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code.
Green and yellow:
EARTH
Blue:
NEUTRAL
Red:
LIVE
As the colours of the wires in the mains lead of this appliance may not correspond with the colour markings in your plug proceed as follows: -
The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E, or coloured
green or coloured green and yellow, or marked with the earth symbol
The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N, or coloured black.
The wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter L, or coloured red.
Fuel effect Pebbles/coal
Once the fire has been installed in the correct position unpack the pebbles/coals from the accessory box and arrange on the fuel bed.
