flamco MeiTronic RCD2 Скачать руководство пользователя страница 18

Страница: 18 / 28

Instructions for use

S1 PARAMETER GROUP - SERVICE PARAMETERS

ADDITIONAL AND

SERVICE SETTINGS

No.

Description

Range

S1.2

ROOM TEMPERATURE

This setting determines which sensor is used for room

temp.

Info: For setting 3, median value of the installed and

auxiliary sensor is calculated for room temp.

0 - none

1 - built-in sensor

2 - auxiliary sensor

(AUX)

3 - built-in and addi-

tional sensor

S1.3

CALIBRATION OF BUILT-IN TEMPERATURE SENSOR

This setting determines the correction of measured

temp. of the built-in sensor.

-5,0 ÷ 5,0 °C (

0,0

)

S1.4

AUXILIARY TEMP. SENSOR (AUX) CALIBRATION

This setting determines the correction of measured

temp. of the auxiliary sensor.

-5,0 ÷ 5,0 °C (

0,0

)

S1.5

RELATIVE HUMIDITY SENSOR CALIBRATION

This setting determines the correction of measured

relative humidity in the room.

-10 ÷ 10 % (

)

S1.6

AIR PRESSURE SENSOR CALIBRATION

This setting determines correction of measured air

pressure.

-100 ÷ 100 mb (

)

S1.7

AIR QUALITY SENSOR CALIBRATION

This setting determines the correction of measured air

quality.

-1000 ÷ 1000 (

)

S1.8

LIGHT SENSOR CALIBRATION

This setting determines the correction of measured

lighting in the room.

0,5÷ 2 (

)

S1.9

LOCKING THE MENU

This setting limits access to parameter groups in the

menu.

0 - no lock

1 - S1

2 - P1, P2 and S1

S1.10

LOCKING BUTTONS

This setting locks button functionality.

Operation of locking buttons function is described in

the chapter »Locking butons«.

0 - no lock

1 - operation type,

2 - same as 1 and

functions,

3 - same as 2 and desi-

red temp.,

4 - same as 3 and info

browsing and settings.

S1.11

MINIMUM SETTING OF REQUESTED TEMP.

This setting determines minimum possible setting of

room temp.

4 ÷ 40 °C (

)

Содержание MeiTronic RCD2





























Результаты поиска

Содержание MeiTronic RCD2

Отзывы:

flamco MeiTronic RCD2, Руководство пользователя, Страница: 18 / 28

Результаты поиска

Содержание MeiTronic RCD2

Отзывы: