FiveFish X-12 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 31

background image

Page 22

Copyright

©

2010 FiveFish Studios

For comments & corrections about this guide, please email [email protected]

www.fivefishstudios.com

X-12 Microphone Preamp Kit

VU Meter Calibration Guide

1. Adjust trimmer resistor so that when you feed a 0dB signal to the VU Meter, the 3

rd

LED lamp lights up.

For +4dBu operation, connect a signal generator to the VU meter input, 1Khz, adjust output of Signal generator to
1.22Vrms, and adjust trimmer resistor until 3

rd

LED lights up.

VU Meter Troubleshooting Guide

Well, hopefully you won’t need this part.

“Measure twice, cut once”… as they say. Take your time assembling the kit, don’t be in a hurry, work carefully and methodically
and you won’t need this troubleshooting guide

Problem: No lights, no LED movement. VU Meter does not work!

Check if there is power applied to the VU Meter Kit. Supply voltage must be at least 5Volts DC.  Check the GND wire is connected.

Check that the LEDs were inserted in the correct orientation. Long leg soldered to the left side.

Check that you installed the jumper headers for JP1, JP2, JP3 and JP4.  All jumpers must be in the HORZ position.

Check that the trimmer resistor is adjusted.

Check that you have signal coming out of your preamp/XLR jack.  Make sure it is strong enough to register on the VU Meter Kit.

«
...
21
22
23
24
25
...
»

Содержание X-12
































Отзывы:

Нет отзывов

Похожие инструкции для X-12

Бренд: Randall Страницы: 9

Бренд: Technics Страницы: 264

Бренд: OM POWER Страницы: 56

Бренд: Akai Страницы: 9

Бренд: Cyrus Страницы: 25

Бренд: Teac Страницы: 28

Apocalypse AP600.2

Бренд: Planet Audio Страницы: 21

Бренд: Marshall Amplification Страницы: 1

Бренд: Rockville Страницы: 12

CLEAN SINK MKII

Бренд: 3rd Power Страницы: 11

Бренд: Toa Страницы: 2

Бренд: Studiomaster Страницы: 6

Бренд: ifi Страницы: 17

Бренд: QSC Страницы: 36

Бренд: Crown Страницы: 2

Redeye 3D Phantom

Бренд: Little Labs Страницы: 6

Бренд: National Instruments Страницы: 14

Бренд: Pioneer Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды