FiveFish Studios NK-72DI Скачать руководство пользователя страница 43

Страница: 43 / 44

NK-72DI Mic DI Assembly Guide

10. TROUBLESHOOTING GUIDE

Hey, we’re all human and make mistakes. Hopefully the tips below will help you troubleshoot your Mic Preamp build.

When I turn the gain knob clockwise, the sound decreases instead of increasing. At minimum gain setting, I have a very loud output signal.

It’s backwards!

Please review Step 3.19 and look closely at how the wires are connected to the potentiometer. You need to swap the location of your 2 wires if your

gain is backwards.

I hear a popping sound when I switch from DI Instrument to Mic Input. I’m using a Condenser microphone with 48Volt phantom power

switched ON.

Turn OFF 48V Phantom Power switch and wait a few seconds before switching between DI Instrument and Mic Input or vice versa. Otherwise, you

may get a popping sound if you switch between the (2) inputs, AND have 48V Phantom Power turned ON.

Содержание NK-72DI



































Результаты поиска

Содержание NK-72DI

Отзывы:

Похожие инструкции для NK-72DI

Бренды по названию

Популярные бренды

FiveFish Studios NK-72DI, Инструкция по сборке

Результаты поиска

Содержание NK-72DI

Отзывы:

Похожие инструкции для NK-72DI

Бренды по названию

Популярные бренды