manualshive.com logo in svg

Fisher EZ easy-e, Инструкция по эксплуатации, Страница: 1 / 36

Поделиться
Скачать
Fisher EZ easy-e Скачать руководство пользователя страница 1

www.Fisher.com

Fisher

™

 EZ easy‐e

™

 Control Valve

Contents

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of Manual

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Educational Services

2

. . . . . . . . . . . . . . . . . . . . . . . . .

Installation

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Packing Lubrication

6

. . . . . . . . . . . . . . . . . . . . . . . . . .

Packing Maintenance

6

. . . . . . . . . . . . . . . . . . . . . . . . .

Replacing Packing

9

. . . . . . . . . . . . . . . . . . . . . . . .

Trim Maintenance

12

. . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lapping Metal Seats on Valves with Plain

and Extension Bonnets

15

. . . . . . . . . . . . . . . .

Assembly

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ENVIRO‐SEAL

t

 Bellows Seal and Bonnet

20

. . . . . . .

Replacing a Plain or Extension Bonnet

with an ENVIRO‐SEAL Bellows Seal
(Stem/Bellows Assembly) and Bonnet

20

. . . .

Replacing an Installed ENVIRO‐SEAL

Bellows Seal (Stem/Bellows Assembly)

22

. . .

Purging the ENVIRO‐SEAL

Bellows Seal Bonnet

24

. . . . . . . . . . . . . . . . . . .

Parts Ordering

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Kits

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts List

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 1. Fisher EZ Valve with 657 Actuator and
DVC6000 Digital Valve Controller

W8120A‐1

Introduction

Scope of Manual

This instruction manual includes installation, maintenance, and parts information for NPS 1/2 through 4 Fisher EZ
valves through CL600 ratings. Refer to separate manuals for instructions covering the actuator and accessories.

Do not install, operate, or maintain an EZ valve without being fully trained and qualified in valve, actuator, and
accessory installation, operation, and maintenance. 

To avoid personal injury or property damage, it is important to

carefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings.

 If you

have any questions about these instructions, contact your 

Emerson sales office

 or Local Business Partner before

proceeding.

Description

EZ valves (figure 1) are globe‐style with integral end connections, post guiding, and quick‐change trim. These valves
are used in chemical or hydrocarbon processing applications or in applications that require control of nonlubricating,
viscous, or other hard‐to‐handle fluids.

Instruction Manual

D100401X012

EZ Valve

November 2017

Содержание EZ easy-e





































Отзывы:

Нет отзывов