background image

Cleaning the Interior

Wash the inside surface of the storage area with warm
water and baking soda solution (about one tablespoon of
baking soda per quart of water). Rinse thoroughly with
clean, warm water and wipe dry. The procedure can also
be used for cleaning the door gasket.

Cleaning the Exterior

Wipe the cabinet exterior occasionally with a cloth damp-
ened in mild detergent, rinse and wipe dry with a soft
cloth. Do not use abrasives or caustic cleaners or scour-
ing pads.

Cleaning the Condenser

Periodic cleaning of the condenser can easily be accom-
plished by brushing the coil with a soft brush and/or using
a vacuum cleaner with a brush attachment. Be sure dirt,
dust and collection of other debris does not build up to a
point where air circulation through the condenser is
restricted.

Condensate Pan (Heated)

This pan is located on the bottom of the cabinet and can
be removed for cleaning by removing the screw that holds
the cover over the electrical plug, unplugging the conden-
sate heater and pulling the pan forward to remove the
cabinet.

Remove and clean all deposits that have built up in the
pan. Care should be taken in replacing the pan to ensure
that the pan is properly placed under the drain line from
the evaporator coil. Frequently cleaning of this pan may
be required in areas of high traffic and humidity.

Removing Door

If the cabinet is too wide to move through narrow door-
ways, the cabinet door can be removed by simply lifting
the door off the hinges while it is in the open position. It
is not necessary to remove the hinge covers to remove
the door.

11

Maintenance

Warning

Be sure power is turned off before
conducting maintenance to the freez-
er.

Содержание Isotemp 13-986-327L





















Отзывы: