background image

Setting the Temperature

To change the set temperature, press and release the

Menu

keypad once.  The display will flash SP and the

Mode LED will be illuminated.  The last set temperature
will then be shown in the display.  To change the tempera-
ture, press the 

UP

or 

DOWN

arrow key.  The adjustable

temperature range is 0 to -30°C (32 to -22°F).  When the
desired set temperature is displayed, press the 

Menu

key-

pad to enter the set temperature and activate the 

Units

Select

menu.

Units Select

The second menu selects the units.  The freezer control
displays temperature in °C or °F.  The factory setting is
°C.  Starting from the temperature display mode (Mode
LED off), press the 

Menu

key twice.  The current temper-

ature units are displayed.  To switch between units, press
the UP or DOWN arrow key to change to the desired
units, then press the 

Menu

key to select.  The desired

unit LED will be displayed on the right of the temperature
display.  

Calibration Offset

In the event the freezer needs calibrated, a simple routine
is available to adjust the display and control point to a ref-
erence standard.  To set the temperature offset, press
and hold the 

Menu

keypad for 5 seconds.  The display

will flash oS (offset) followed by the last temperature off-
set value.  The factory setting is 0.  To change the offset
value, press the UP or DOWN arrow key, then press the

Menu

key.  The value shown in the display will be added

to the previous temperature reading.  The maximum off-
set value is ±5°C (±9°F).

For Example:
The freezer has been operating at -15°C for 30 minutes.
The display indicates -15°C but a reference thermometer
in the chamber indicates -17°C.  The operator presses
and holds the 

Menu

keypad for 5 seconds and changes

the offset value from 0 to -2.  The 

Menu

key is pressed

until the 

Mode

LED goes out.  Now the display indicates a

11

O

PERATION

Содержание Isotemp 13-986-223F





















Отзывы: