background image

13

24

The chart below shows how your GoldBug2’s sensitivity and ability 

to  operate  in  mineralized  soil  is  affected  by  each  combination  of 

MINERALIZATION and MODE settings.

 

In either the BOOST or NORMAL mode, the GoldBug2’s sensitivity 

decreases as you increase MINERALIZATION settings from LOW to HIGH. 

MINERALIZATION CONTROL

In general, you should start searching with the MINERALIZATION set to 

LOW. If you experience too much “ground chatter”, even after adjusting 

the GROUND REJECT in the LOW MINERALIZATION mode, try reducing 

the sensitivity or set the MINERALIZATION to NORMAL. If that does 

not do the trick, set the MINERALIZATION to HIGH and readjust the 

GROUND REJECT control. If there is still to much “ground chatter,” 

reduce the SENSITIVITY . 

In the LOW MINERALIZATION setting, the searchcoil response (retune 

speed) is slow and the circuit gain (amplification) is high. In the NORMAL 

MINERALIZATION setting, searchcoil response is fast and the circuit 

gain is reduced slightly. In the HIGH setting, response is fast and the 

gain is further reduced.

Moist, alkali soil conditions will usually require use of the NORMAL or 

HIGH MINERALIZATION settings. Heavy, black sand conditions will 

usually require the HIGH MINERALIZATION setting.

MODE AND MINERALIZATION BUTTON SELECTION

Mineralization

setting in

NORMAL MODE

Figure 7.

A false signal occurs when something that should not sound like a good 
target sounds like one. For example, the GoldBug2 may detect metal in 
your boots if you swing your searchcoil too close to your feet. Here are 
some other sources of false signals, and here is what to do about them.

1.  Hot Rocks: Mineralized rocks that respond like metal.
  Solutions: Most hot rocks seem to be on top of the ground, so 

you can just kick them out of the way and recheck the ground 
beneath them. The GoldBug2 will ignore some hot rocks. Certain 
other types of hot rocks have their own distinctive sound, which 
you will learn to recognize. Or you can “tune-out” most hot rocks 
in the air or on the ground by adjusting the GROUND REJECT 
knob right over the rock. If is a nugget, you will not be able to 
tune it out unless is very small. Many strong hot-rock signals will 
disappear rapidly when you lower the sensitivity level, whereas 
a strong nugget signal will just get weaker. Of course, the best 
way to check a possible hot rock is to flip your mode switch 
into “DISC mode”. 

2. Highly Mineralized Soil: Unfortunately, this is where most 

nuggets are found. The GoldBug2 will handle all but the very 
worst soil.

  Solutions: Switch to the HIGH mineralization setting. Ground 

adjust very carefully and often. Lower the sensitivity. Ground 
adjust to a height just high enough to eliminate most false 
signals and adjust your stem length to sweep at that height. 

3.  Dissolved Salts: On a wet ocean beach or moist inland soil.
 Solutions: 

Same as highly mineralized soil. 

FALSE SIGNALS

Содержание Gold Bug-2





































Отзывы: