background image

PROBLEMS AND SOLUTIONS GUIDE

Vehicle was running but 

Loose wires or loose connectors 

Check all wires and connectors. Make sure the battery 

suddenly stopped 

 

 connector is tightly plugged into the motor connector,  

and that there are no loose wires around the motors.

 

Tripped thermal fuse 

 The built-in thermal fuse may "trip" and shut down operation 

of the vehicle if the vehicle is overloaded or the driving 

conditions too severe. The fuse will automatically reset 

itself after approximately 25 seconds, allowing the vehicle 

to resume normal operation. To avoid repeated automatic 

shutdowns, do not overload the vehicle by exceeding the  

40 lb maximum weight capacity or by towing anything 

behind the vehicle. Do not drive up hills or run into fixed 

objects, which can cause the wheels to stop spinning while 

power is still being supplied to the motors. If a thermal 

fuse continually trips, contact your local Power Wheels

®

 

authorized service center.

Short run time (Less than  

Undercharged battery 

Charge the battery. A new battery should have been 

1 - 3 hours per charge) 

 

charged for at least 18 hours before using the vehicle for 

 

 

the first time. After first-time use, recharge the battery for 

 

 

at least 14 hours after each use. Never charge the 

 

 

battery longer than 30 hours.

 

 

Check all wires and connectors. Make sure the battery 

 

 

connector is tightly plugged into the charger connector, and  

 

 

that the charger is plugged into the wall. 

 

 

Make sure power flow to the wall outlet is “ON”.

 

Overcharged battery 

Do not charge the battery longer than 30 hours. If you  

 

 

suspect that your battery is damaged as a result of  

 

 

overcharging, contact your local Power Wheels

®

 authorized  

 

 

service center. They can test the battery for you.

 

Battery is old and will not 

Even with proper care, a rechargeable battery does not  

 

accept full charge 

 last forever. Average battery life is 1 to 3 years depending 

on vehicle use and use conditions. Replace only with a 

Power Wheels

®

 6 Volt (4.0 Amp/Hr.) battery with built-in 

thermal fuse. 

Do not substitute parts.

 

Tripped thermal fuse 

 The built-in thermal fuse may "trip" and shut down operation 

of the vehicle if the vehicle is overloaded or the driving 

conditions too severe. The fuse will automatically reset 

itself after approximately 25 seconds, allowing the vehicle 

to resume normal operation. To avoid repeated automatic 

shutdowns, do not overload the vehicle by exceeding the  

40 lb maximum weight capacity or by towing anything 

behind the vehicle. Do not drive up hills or run into fixed 

objects, which can cause the wheels to stop spinning while 

power is still being supplied to the motors. If a thermal 

fuse continually trips, contact your local Power Wheels

®

 

authorized service center.

 

PROBLEM

 

POSSIBLE CAUSE

 

SOLUTION

18

J4030pr-0920

18

N

J7825a-0920

Содержание LIL'QUAD





















Отзывы: