background image

Soothing Unit

• Make sure your child is properly secured in the seat.

• Slide the power switch to:

Vibrations

Off

IMPORTANT!

Low battery power causes this product to operate

erratically: no vibrations and the product may not turn off.
Remove and discard the battery and replace with a new 
LR20 (“D”) 

alkaline

battery.

• Lift the blanket and tuck baby in!

8

• The pad and blanket are machine washable. Wash them

separately in cold water on the gentle cycle. Do not use
bleach. Line dry only.

• The frame and toys may be wiped clean using a mild

cleaning solution and a damp cloth. Do not use bleach.
Do not use harsh or abrasive cleaners. Rinse clean with
water to remove residue.

To remove the pad:

First remove the bottom pocket of the

pad 

. Then, remove the upper pad flap 

.

To replace the pad, 

refer to Assembly steps 7 and 8.

GREAT BRITAIN
Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500302.

AUSTRALIA

Mattel Australia Pty. Ltd., 658 Church Street, 
Locked Bag #870, Richmond, Victoria 3121 Australia. 
Consumer Advisory Service 1300 135 312.

ASIA

Mattel East Asia Ltd, Room 1106, South Tower, 
World Finance Centre, Harbour City, Tsimshatsui, HK, China.

MALAYSIA

Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P) 
Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf
Country Resort, 47410 PJ. Tel: 03-78803817, Fax: 03-78803867.

Care

Consumer Information

Power Switch

Содержание H5124









Отзывы: