background image

16

FCC Statement (United States Only)

This equipment has been tested and found 
to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the 
FCC Rules. These limits are designed to 
provide reasonable protection against 
harmful interference in a residential 
installation. This equipment generates, uses 
and can radiate radio frequency energy 
and, if not installed and used in accordance 
with the instructions, may cause harmful 
interference to radio communications. 
However, there is no guarantee that 
interference will not occur in a particular 
installation. If this equipment does cause 
harmful interference to radio or television 
reception, which can be determined by 
turning the equipment off and on, the 
user is encouraged to try to correct the 
interference by one or more of the 
following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the 

equipment and receiver.

•  Consult the dealer or an experienced 

radio/TV technician for help.

Note:

 Changes or modifications not 

expressly approved by the manufacturer 
responsible for compliance could void the 
user’s authority to operate the equipment.
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions: (1) this device 
may not cause harmful interference and 
(2) this device must accept any interference 
received, including interference that may 
cause undesired operation.

ICES-003

This Class B digital apparatus complies with 
Canadian ICES-003. Operation is subject to 
the following two conditions: (1) this device 
may not cause harmful interference and 
(2) this device must accept any interference 
received, including interference that may 
cause undesired operation.

NMB-003

Cet appareil numérique de la classe B est 
conforme à la norme NMB-003 du Canada. 
L’utilisation de ce dispositif est autorisée 
seulement aux conditions suivantes : 
(1) il ne doit pas produire de brouillage et 
(2) l’utilisateur du dispositif doit être prêt 
à accepter tout brouillage radioélectrique 
reçu, même si ce brouillage est susceptible 
de compromettre le fonctionnement 
du dispositif.

Consumer Information

Содержание BMF34

















Отзывы: