background image

8

Battery Installation    

배터리 장착

배터리 장착

1

2

1

2

1

+

1,5V

D (LR20)

•  Protect the environment by not disposing of 

this product with household waste (2002/96/
EC). Check your local authority for recycling 
advice and facilities.

• 

환경 보호를 위해 본 제품을 생활 

쓰레기와 혼합해 배출하지 마십시오

(2002/96/EC). 재활용 방법과 시설에 

대해서는 관할 시군구청에 문의하시기 

바랍니다.

Hint: 

We recommend using an 

alkaline

 battery 

for longer battery life.

도움말:

도움말: 배터리를 오래 쓰시려면 알카라인

알카라인 

배터리 사용을 권장합니다.

Soothing Unit

•  Pull to remove the pad from around the 

retainers and the soothing unit 

1

.

•  Remove the pad bottom pocket from the 

footrest 

2

.

진동박스

진동박스

• 

고정장치와 진동박스 가장자리에서 

패드를 빼냅니다 

1

.

• 

패드 하단 포켓을 발 받침대에서 

벗깁니다 

2

.

•  Loosen the screw in the battery compartment 

door. Remove the battery compartment door.

•  Insert one D (LR20) 

alkaline

 battery into the 

battery compartment.

•  Replace the battery compartment door and 

tighten the screw.

•  Pull and fit the pad seat bottom pocket around 

the soothing unit and footrest.

•  If this product begins to operate erratically, you 

may need to reset the electronics. Slide the 
power switch off and then back on.

• 

배터리 장착부 덮개의 나사를 풀어 덮개를 

분리합니다. 

• 

배터리 장착부에 D (LR20) 알카라인

알카라인 

배터리 하나를 장착합니다.

• 

덮개를 제자리에 끼우고 나사를 조입니다.

• 

패드 하단 포켓을 진동박스와 발 받침대에 

끼웁니다.

• 

본 제품이 오작동하기 시작하면 

전자장치를 리셋해야 합니다. 전원 

스위치를 껐다가 다시 켜십시오.

Содержание BBT60













Отзывы: