Fisher & Paykel OB60Series, Руководство по установке, Страница: 3 / 8

LOWER TRIM
OVEN DOOR
LOWER TRIM
AIR FLOW
FEET
PRIOR TO INSTALLATION
UNPACKING THE OVEN
3
4
5
ELECTRICAL CONNECTION
Before you install the oven, make sure that
the benchtop and oven cavity are square and level, and are the required dimensions
the installation will comply with all clearance requirements and applicable standards and regulations
a suitable isolating switch providing full disconnection from the mains power supply is incorporated in
the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations.
The isolating switch must be of an approved type and provide a 3 mm air gap contact separation
in all poles (or in all active [phase] conductors if the local wiring rules allow for this variation of the
requirements)
the isolating switch will be easily accessible to the customer with the oven installed
there is at least 1.5 m (and not more than 2 m) free length of power supply cable within the cavity for
ease of installation and servicing
the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall
the oven will rest on a surface that can support its weight
the height from the floor suits the customer
you consult local building authorities and by-laws if in doubt regarding installation.
Important!
Some environmental factors and cooking habits can cause condensation in and around the oven during use.
To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we
recommend moisture-proofing the oven cavity.
Important!
This oven must be connected to the mains power supply only by a suitably qualified person.
This oven must be earthed.
Before connecting the oven to the mains power supply, check that
the domestic wiring system is suitable for the power drawn by the oven
(as specified on the rating plate)
the voltage corresponds to the value given on the rating plate.
Important!
Do not lift the oven by the door handle.
Remove all packaging and dispose of it responsibly. Recycle items that you can.
Place the unpacked oven onto wooden blocks or similar supports to prevent damaging the lower trim.
You may remove the feet, but ensure the oven does not sit on the lower trim
Important!
The lower trim ensures correct air circulation and allows the door to open and close without obstruction. The
manufacturer does not accept any responsibility for damage resulting from incorrect installation.
OB60B & OB60D MODELS
OB60S & OB60N MODELS
Model code Power Voltage
OB60SLC... 2350-2550 W 230 - 240 V~
OB60SLM... 3070 W 220-240 V~
OB60SCE... 3070 W 220-240 V~
OB60SCM... 3070 W 220-240 V~
OB60SCT... 3600 W 230 V~
OB60SDT... 3600 W 230 V~
OB60S9D... 3400 W 220-240 V~
OB60SV... 3070 W 220-240 V~
OB60NL... 2050 W 220-240 V~
OB60NC... 2800 W 220-240 V~
OB60ND... 2800 W 220-240 V~
Model code Power Voltage
OB60BC... 5800 W 220 - 240 V~
OB60BD... 5800 W 220 - 240 V~
OB60B77C... 5850 W 220 - 240 V~
OB60B77D... 5850 W 220 - 240 V~
OB60DD... 6120 W 220 - 240 V~
E
N L
1
(L )
2
Unhook to open cover
1
2
Unscrew to open
cable clamp
E N L
1
(L )
2
Green & Yellow
(Earth)
Brown (Live)
Blue (Neutral)
N L
D
1
2
Unscrew to
remove cover
plate
Unscrew to remove
cable clamp
(2,1) -1- 599790F OB60&OB90 installA2 NZGB.indd 24/05/13 2:37 PM (2,1) -1- 599790F OB60&OB90 installA2 NZGB.indd 24/05/13 2:37 PM