background image

517762 

18 

7.3.1 

Testing the Conductivity Contacts  

Impedance Testing 

It is possible to check the integrity of the conductivity contacts through diagnostics.  Firstly enter 
the diagnostic mode described in Section 7.1.4, and then press the 

Time Dry

 button five times.  In 

this mode, touching damp clothes or fingers across the conductivity contacts will cause the LED 
display to change.  If the contacts, or the harness to them, have gone open circuit, no change will 
occur in the LED display.  This is a useful method of checking the integrity of the sensor cells.  To 
exit the diagnostic mode, press the 

Power

 button. 

 

Resistance Test 

An alternative, but slightly less reliable method of testing the conductivity contacts, is to test the 
circuit with a multimeter.  When using this method the power to the dryer must be switched off.  
Place one probe of the multimeter on each conductivity contact.  The resistance should be 
6. 2%. 
 
To exit the diagnostic mode, press the 

Power

 button. 

7.3.2 

Data Download Mode 

Encoded data is transmitted out of the 

Wrinkle Free

 LED, and can be captured by an optical 

download pen attached to a PC or hand held palm PC, where “Smart Tool” software interprets the 
data to aid servicing. 
 
To enter the Data Download mode; 
 
Enter diagnostic mode as described in Section 7.3, then press the 

Start/Pause 

button.  The 

Wrinkle Free

 LED will flash.  Place the data download pen over the LED to download the data. 

 
To exit from the data download mode, press the 

Power

 button. 

 

8 AUTOSENSING 

 

When wet or damp clothes are loaded into a dryer they are partially saturated with water, which is 
a relatively good conductor of electricity. In the Intuitive™ dryer, sensor bars (located beneath the 
lint bucket) are used to measure the conductivity. When moisture in the clothes touches across the 
sensor bars their conduction is measured. As the clothes dry they become less conductive and it is 
this measurement that is used to calculate the dryness of the clothes load.  Large loads will brush 
against these sensor bars more frequently than small loads, and this strike count is used to help 
determine the dryness of different sized loads. 
 
Different fabrics retain moisture differently; a thick towel containing a lot of moisture will often 
conduct the same as a light synthetic garment containing very little. It is this difference in fabric 
characteristics plus the initial unknown moisture content that makes the calculation of dryness 
reasonably complex.  To test the sensor bars refer to Section 7.3.1 
 

9 TEMPERATURE 

CONTROL 

Auto sensing is automatically selected when the Intuitive™ dryer is turned on. The user can select 
a time dry option of 20, 40 or 80 minutes through the Options menu. Auto sensing of the clothes 
load dryness level is achieved by touch sensors that sense the moisture content of the load.  An 
exhaust temperature sensor is used to monitor the exhaust temperature. The controller limits the 
temperature to what is required for the various cycles and determines what elements are used.   

Содержание Intuitive DE62T27GW


























Отзывы: