Fisher & Paykel DW60U2I2 Скачать руководство пользователя страница 4

4

SAFETY AND WARNINGS

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to 

change at any time. For current details about model and specification availability in your country, 

please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

WARNING!

To reduce the risk of fire, injury to persons or damage when using the appliance, follow the 

important safety instructions listed below. Read all the guidance before using the appliance. 

Servicing

 

z

Do not repair or replace any part of the appliance unless specifically recommended in 

this guide. All other servicing should be undertaken by a Fisher & Paykel trained and 

supported service technician or qualified person.

Installation

 

z

Ensure all water connections are turned OFF. It is the responsibility of the plumber and 

electrician to ensure that each installation complies with all Codes and Regulations.

 

z

The dishwasher MUST be installed to allow for future removal from the enclosure if 

service is required.

 

z

The switched power outlet must be outside the dishwasher cavity, so that it is 

accessible after installation.

 

z

This dishwasher is manufactured for indoor use only.

 

z

Care should be taken when the appliance is installed or removed to reduce the 

likelihood of damage to the power supply cord and hoses.

 

z

If the dishwasher is to be relocated from one installation to another it must be kept 

upright to avoid damage from water spillage.

 

z

Make sure only new hoses are used for connection (supplied with the dishwasher). Old 

hoses should not be reused.

 

z

Failure to install the dishwasher correctly could invalidate any warranty or 

liability claims.

 

z

Ensure the dishwasher is placed between cabinetry. Failure to do so may result in an 

unstable product, which may cause damage or injury.

 

z

Do not operate this appliance if it is damaged, malfunctioning, partially disassembled 

or has missing or broken parts, including a damaged power supply cord or plug.

 

z

Do not store or use petrol, or other flammable vapours and liquids in the vicinity of the 

dishwasher.

 

z

Connect to a properly rated, protected and sized power supply circuit to avoid 

electrical overload.

 

z

Make sure that the power supply cord is located so that it will not be stepped on, 

tripped over or otherwise subject to damage or stress.

 

z

Do not install or store the dishwasher where it will be exposed to temperatures below 

freezing or exposed to weather.

 

z

Do not use an extension cord or a portable electrical outlet device (e.g. multi-socket 

outlet box) to connect the dishwasher to the power supply.

 

z

This appliance must be earthed. In the event of a malfunction or breakdown, earthing 

will reduce the risk of electric shock by providing a path of least resistance for 

electric current.

 

z

This appliance is equipped with a cord having an equipment-earthing conductor and 

an earthing plug. The plug must be plugged into an appropriate outlet that is installed 

and earthed in accordance with all local codes and ordinances.

 

z

EARTHING INSTRUCTIONS - This appliance must be connected to a earthed metal, 

permanent wiring system, or an equipment-earthing conductor must be run with 

the circuit conductors and connected to the equipment-earthing terminal or lead on 

the appliance.

 

z

Ensure the product is not plugged in when fitting custom panels.

 

z

Installation of custom panels requires basic mechanical and electrical skills.

 

z

Installation must comply with your local building and electricity regulations.

 

z

Failure to install the custom panels correctly could invalidate any warranty or 

liability claims.

 

z

Installation of this dishwasher requires basic mechanical and electrical skills.

 

z

Be sure to leave these Instructions with the Customer.

 

z

Installation must comply with your local building and electricity regulations.

 

z

At the completion of the dishwasher installation, the Installer must perform the 

Final Checklist.

 

z

Remove all packaging materials supplied with the dishwasher.

 

z

If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring 

the vehicle, boat or mobile facility containing the product to the service shop at your 

expense or pay the service technician's travel to the location of the product.

Содержание DW60U2I2





















Отзывы: