Fisher & Paykel DISHDRAWER DD60DDFHX9 Скачать руководство пользователя страница 17

1

1

   SAFETY AND WARNINGS

 

WARNING!

Electrical shock hazard
Before installing the dishwasher, remove the 
house fuse or open the circuit breaker.
This appliance must be earthed. In the event 
of a malfunction or breakdown, earthing will 
reduce the risk of electric shock by providing 
a path of least resistance for electric current. 
This appliance is equipped with a cord having 
an equipment-earthing conductor and an 
earthing plug. The plug must be plugged into 
an appropriate outlet that is installed and 
earthed in accordance with all local codes and 
ordinances. 

WARNING- Improper connection of the 
equipment-earthing conductor can result in a 
risk of electric shock. Check with a qualified 
electrician or service representative if you are 
in doubt as to whether the appliance is properly 
earthed.
Do not modify the power supply plug provided 
with the appliance - if it will not fit the outlet, 
have a proper outlet installed by a qualified 
electrician. Do not use an extension cord, 
adapter plug or multiple outlet box. 
Failure to follow this advice may result in 
electrical shock or death.

 

WARNING!

Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or 
cuts.

!

!

  IMPORTANT SAFETY INSTRUCTIONS 

 

Installation of this dishwasher requires basic 
mechanical and electrical skills.

 

Be sure to leave these Instructions with the Customer.

 

Installation must comply with your local building and 
electricity regulations.

 

At the completion of the dishwasher installation, the 
Installer must perform the Final Checklist.

 

Remove all packaging materials supplied with the 
dishwasher.

 

This dishwasher is manufactured for indoor use only.

 

Ensure all water connections are turned OFF. It is the 
responsibility of the plumber and electrician to ensure 
that each installation complies with all Codes and 
Regulations.

 

The dishwasher MUST be installed to allow for future 
removal from the enclosure if service is required.

 

The switched power outlet must be outside the 
dishwasher cavity, so that it is accessible after 
installation.

 

Care should be taken when the appliance is installed 
or removed to reduce the likelihood of damage to the 
power supply cord and hoses.

 

If the dishwasher is to be relocated from one 
installation to another it must be kept upright to avoid 
damage from water spillage.

 

Make sure only new hoses are used for connection 
(supplied with the dishwasher). Old hoses should not 
be reused.

 

Failure to install the dishwasher correctly could 
invalidate any warranty or liability claims.

 

If the product is installed in a motor vehicle, boat or 
similar mobile facility, you must bring the vehicle, boat 
or mobile facility containing the product to the service 
shop at your expense or pay the service technician’s 
travel to the location of the product.

Содержание DISHDRAWER DD60DDFHX9

































Отзывы: