Fisher & Paykel DD24DCT Скачать руководство пользователя страница 19

18

!9

 

FINAL CHECKLIST

TO BE COMPLETED BY THE INSTALLER

Complete and keep for safe reference:

Model    

Serial No. 

Purchase Date 

Purchaser 

Dealer Address  

Installer’s Name 

Installer’s Signature  

Installation Company

Installation Date 

Check all parts are installed.

Ensure that all panels and parts thereof are secure and final electrical tests have been 
conducted in accordance with local electrical regulations.

Ensure product is level, securely fastened to the cabinetry and opens and closes freely. 
The drawers must be free to fully close with no resistance from the cabinetry.

Ensure inlet hose to water supply has supplied rubber washer fitted, and that it’s 
tightened a further half turn after seal contact.

Ensure any knockouts or plugs in drain connection have been drilled out and drain 
connection has been made.

The drain hose joiner must not support the weight of excess hose material. Keep drain 
hose as fully extended as possible to prevent sagging. Any excess length of drain hose 
should be kept on the dishwasher side of the highloop.

If connecting the drain hose to the sink trap, ensure the Highloop is a minimum 150 mm 
higher than the drain hose joiner.

Ensure any packaging or tape securing the racks is removed from the drawers.

Water softener models only: adjust the water softener setting from the default setting to 
suit the water hardness of the area. 
See the Quick start guide and section ‘Water softener’ in the User guide.

Turn on the power and water supplies, then open the drawers. You should hear a 
beep and see a program indicator light up on the internal control panel.

Check the spray arms are in place, mounted correctly and free to rotate, by 
physically rotating by hand.

Add three cups of water into the drawer. Press 

 until the indicator of the ‘Rinse’ 

program lights up. Close the drawer and press 

 to start the program. 

Repeat for the other drawer.

After the Rinse program has finished, ensure the dishwasher has run and drained 
correctly.

Check the water supply has correctly shut off and drainage connection for leakage. 

Spray arm

Copyright © Fisher & Paykel Appliances 2017. All rights reserved.

The product specifications in this booklet apply to the specific products 
and models described at the date of issue.  Under our policy of continuous 
product improvement, these specifications may change at any time.  You 
should therefore check with your Dealer to ensure this booklet correctly 

describes the product currently available.

FISHERPAYKEL.COM

Содержание DD24DCT





















Отзывы: