background image

2

SAFETY AND WARNINGS

!

 WARNING!

Electric Shock Hazard

Failure to follow this advice may result in 

electric shock or death.

•  Disconnect the appliance from the mains 

electricity supply before carrying out any work or 

maintenance.

•  Connection to a good earth wiring system is 

essential and mandatory.

•  Alterations to the domestic wiring system must 

only be made by a qualified electrician.

!

 WARNING!

Cut Hazard

Failure to use caution could result in injury.

•  Take care: some edges are sharp.

READ AND SAVE THIS GUIDE

General Use

 

z

Read these instructions carefully before installing this product.

 

z

Save these instructions for the local electrical inspector’s use.

 

z

Installation must comply with your local building and local electricity regulations.

 

z

Electrical installation (including electrical grounding) must be done in accordance 

with the National Electrical Code, ANSI/NFPA70 – latest edition and/or local codes. In 

Canada: Electrical installation must be in accordance with the current CSA C22.1 Canadian 

Electrical Codes Part 1 and/or local codes. Particular attention shall be given to the 

relevant requirements regarding ventilation.

 

z

This appliance is to be installed and serviced only by fisher & Paykel trained and 

supported service technician or qualified person.

 

z

The manufacturer accepts no responsibility for the incorrect installation of appliances. 

Incorrect installation may result in personal injury, damage to property and may invalidate 

any warranty or liability claims.

 

z

Do not modify this appliance.

 

z

Do not use or store flammable materials on or near this appliance.

 

z

Packing elements (eg plastic bags, polystyrene foam, staples, packing straps etc) and 

tools should not be left around during and after installation, especially if they are within 

easy reach of children, as these may cause serious injuries.

 

z

Make sure you recycle the packaging material.

 

z

Before disposing of any appliance, make sure that it can no longer be used and that all 

hazardous parts are removed or made harmless, so that children playing with the old 

appliance cannot harm themselves.

 

z

Only genuine replacement parts may be used for servicing the appliance. These are 

available from your nearest Fisher & Paykel Service Center.

 

z

This cooktop requires adequate supply of cool air to fully function. The base of the 

cooktop must have direct unrestricted ventilation to the room where the cooktop is 

installed. There must be a 5mm air gap at the front of the cooktop as shown on diagram 

above in ‘Venting Clearances’. Follow the requirements shown.

 

z

This cooktop must be connected to the mains power supply only by a suitably 

qualified person.

 

z

To connect the cooktop to the mains power supply, do not use adapters, reducers, or  

branching devices, as they can cause overheating and fire.

 

z

The power supply cable must not touch any hot parts and must be positioned so that its  

temperature will not exceed 165°F (75°C) at any point.

Содержание CE244DTB1























Отзывы: