Use
Helmet fitting
You will only ensure optimal protection if your helmet fits just right.
The helmet must not rest on the back of your head, but should not
be pulled too low on your forehead either and must
not be shifted to the left or right.
Adjusting the helmet on the
inside
This helmet features a new, patented
fitting ring with a rotary mechanism.
The size can easily be set with one
hand.
• Place the helmet level on your head
with the fitting ring open. The bottom
edge of the helmet must rest 1-2
finger-widths above the top of your
nose.
• If the helmet can easily be moved,
the fitting ring (1) must be set tight-
er. You do this using the rotary knob
(2). Turning it clockwise makes the
circumference of the fitting ring
smaller, turning it anti-clockwise
make it bigger.
• Tighten the fitting ring until it fully encircles
your head and does not become loose.
Adjusting the straps
In case of a fall, the helmet only protects your
head optimally if the straps are correctly adjust-
ed.
• Place the two Y-shaped strap holders (3)
approx. 1 cm below your ears. The straps at
the back go round the back of your head at
this point.
• Fasten the helmet latch underneath your chin
(Fig. 4). The chinstrap must be pulled taut but
not too tight. You should be able to
still open your mouth slightly when
the buckle is fastened. The correct
position for the fastened chinstrap is
underneath the lower jaw, between
the point of your chin and your
throat.
WARNING:
Always wear the helmet
with the chinstrap fastened.
• If any of the straps are too long or
too short, these can be adjusted
simply by pulling them.
• If the helmet does not fit the size
of your head after all, you should
choose another size or another hel-
met.
Helmet additional lighting
Press the black button to switch on the additional helmet lighting.
Function: 1 continuous light - 2 flash-
ing light - 3 running light - 4 off
Changing the battery
Release the additional helmet lighting
on the inside of the bicycle helmet
by pressing the release button.
The helmet lighting can be
removed. Open the battery cover
with a coin. Pay attention to the
polarity of the battery. Battery
type: Button cell CR 2032 3V.
• Do not use rechargeable batter-
ies.
• Remove leaking batteries
immediately. When doing so,
avoid contact with the skin. In
the event of contact with the
skin, thoroughly clean the areas
affected with water.
• LED class 1: There is no hazard from the light if used correctly.
• After use the batteries may be handed over free of charge
at authorised battery collection points. The end user is legally
obliged to return the batteries to an authorised collection point.
ATTENTION:
Please bear in mind that the illuminated ring system
is only an additional form of lighting. This does not replace lighting
according to the Road Traffic Licensing Regulations.
Cleaning
Use only water, mild soap and a soft cloth for cleaning your
helmet. Do not use solvents like spirit or petrol. Solvents may attack
the helmet skin. The internal pads are washable at 30°.
Disposal
The packaging and ancillary packing consist entirely of environ-
mentally-friendly materials. They can be disposed of at your local
recycling facility.
Contact your local refuse disposal authority for more details of how
to dispose of your worn out product.
Disposal of batteries
Used batteries must not in any event be put in the domestic
refuse. Hand these in to your dealer or your public collection
point for recycling.
Informationes
Guarantee
With this product you receive a guarantee that is valid from the date
of purchase.
In the event of a fault in its functions occurring during the guarantee
period, please send the helmet to the listed service address making
reference to the following model number: FZ-027. Spare parts such
as internal pads and strap clasps can be ordered at the service
address below.
Service:
MTS Group
MTS MarkenTechnikService GmbH & Co. KG
Carl-Benz-Straße 2 · 76761 Rülzheim · Germany
www.mts-gruppe.com.de
Declaration of conformity
*
* The product satisfies the regulation on personal protective equip-
ment (EU) 2016/425.
Tested in accordance with EN 1078:2012+A1
** The declaration of conformity can be viewed via the following
link: http://iuqr.de/FZ027
Address of the notification body:
TÜV Rheinland LGA Products GmbH
Tillystraße 2 · D-90431 Nürnberg
Notified Body 0197
Status 11/20
3
6
4
5
