background image

1

2

3

4

5

6

7

Control Buttons and Items on Keypad

1.  ON/OFF LED.  It is located on the upper right-hand corner of the keypad.  When this LED is lit in 

green, the controller is ready for automatic operation.  When it is lit in red, the controller can be 

started in manual only (display screen will show “OFF”).

2.  Display Screen.  A four-character display that shows programming values and the pressure 

reading.

3.  Three vertical LEDs.  To the right of the display screen, these represent the incoming sensing 

line pressure status. The upper green LED is lit when the pressure the controller measures is 

above the Stop Pressure point, the middle amber LED is lit when the pressure is in between the 

Start Pressure and Stop pressure points and the bottom red LED is lit when the pressure is be-

low the Start Pressure point.

4.  Arrow Pushbuttons.  The Up/Down (+/-) arrow buttons are used for increasing or decreasing 

a parameter value shown on the screen.  The Left/Right buttons are used to scroll through the 

five available programming settings.

5.  Enter Pushbutton.  Looks like a check-mark inside of a gear.  This is used to access the pa-

rameters to program and to confirm programming changes.  The programming procedure is 

described below.

6.  ON/OFF Pushbutton.  This is located on the lower right-hand corner of the keypad.  This is used 

to place the controller in manual/non-automatic mode (display screen will show “OFF”) or 

place the controller in automatic mode.

7.  Start and Stop Pushbuttons.  These are on the left-hand side of the keypad.  Pressing the green 

Start pushbutton starts the pump in manual mode. If the pump is started in manual mode, it 

must be stopped manually by pressing the Stop Pushbutton.  If the controller starts the pump 

in automatic mode by the system pressure dropping to or below the Start Pressure point, 

pressing the STOP button will stop the motor for as long as the button is held pressed. The mo-

tor will restart once button is released.

5

Содержание FTA560E















Отзывы: