background image

 

PB42 CF BonFyre 

(sku# 94500772) 

 

Page 2 of

 

10 

17602206 — 5/3/21 

© Travis Industries, Inc.  

 Ember-Glo™ Glass and Ember Material Installation (GSR2 ONLY)  

Ember bed Glass Installation 

The Ember-Glo™ lights come standard on the GSR2 units.  There is an optional accessory for GSB2 or MV units.  If the 
upgrade kit is not used for the GSB2 or MV units, you may skip this section and proceed to Ember Installation. 

  Make sure the ember skirt is in place.  The skirt hooks over the front of the ember platform and slopes outward 

toward the glass.  The skirt helps keep the glass and ember material from falling off the platform when the glass 
is removed. 

  Locate the perforations in front of the log grate.   

 

  Place a thick layer of the ember glass over the perforations making sure to cover all of the holes completely. 

 

  Lightly dress the ember glass with the black touch-up paint provided.  Check the appearance with the lights on 

and add additional paint, as needed, for a realistic glowing ember appearance.    

NOTE:  

If power is supplied 

to the fireplace it can help 
to turn the lights on while 
painting so you can 
determine an appropriate 
amount of paint for a 
realistic ember appearance. 

 

NOTE:

  We recommend 

that you use a piece of 
paper, cardboard as a 
shield to mask the log grate 
and burner from overspray 
(see below).   

  

 

 

Ember Material Installation 

(GSR2 ONLY) 

  Once the ember glass installation is complete, place 

a generous amount of ember material on the firebox 
floor on either side of the firebox.  Completely cover 
any visible metal on the firebox floor. 

NOTE:

  Make sure no ember material is placed directly on 

the burner.  

HINT:

  Add a few randomly placed ember chunks over the 

ember bed glass to produce a more realistic appearance.   
 

 

 
 

Содержание 94500772











Отзывы: