Firenzo Encore Urban wet Скачать руководство пользователя страница 4

Encore Urban Wet 

2.   INSTALLATION RESPONSIBILITIES 

 

WARNING:

 THE APPLIANCE AND FLUE SYSTEM SHALL BE INSTALLED 

IN ACCORDANCE WITH AS/NZ 2918 AND THE APPROPRIATE 
REQUIREMENTS OF THE RELEVANT BUILDING CODE OR CODES. 
 
ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN 
APPROVED IN WRITING BY THE TESTING AUTHORITY IS 
CONSIDERED 
TO BE IN BREACH OF THE APPROVAL GRANTED FOR COMPLIANCE 
WITH AS/NZS 4013. 

 

CAUTION:

  MIXING OF APPLIANCE OR FLUE-SYSTEM COMPONENTS FROM 

DIFFERENT SOURCES OR MODIFYING THE DIMENSIONAL SPECIFICATION 
OF COMPONENTS MAY RESULT IN HAZARDOUS CONDITIONS.  WHERE 
SUCH ACTION IS CONSIDERED, THE MANUFACTURER SHOULD BE 
CONSULTED IN THE FIRST INSTANCE. 
 
Strict adherence to these instructions will meet these standards. 
Any variation from these installation instructions or any doubt about them must be 
checked against the requirements of the Standards. 
 

Please leave this manual with the owner when installation is complete

 
 
 

3.   FLOOR PROTECTOR REQUIREMENTS 

 
The heater should always be installed on top of its base due to high temperatures 
sustained over long periods.  The base must be anchored to both the floor protector and 
the floor for seismic restraint.  Anchor points are provided in the base.  
 
If the heater is installed on or within 500mm of a heat sensitive floor, 

then an ash 

floor

 

protector to NZS2918 Section 2.2  will be required

.  This floor protector shall 

extend under the appliance and not less than 300mm beyond the front of the fuel 
loading or ash removal openings.  The width of the floor protector shall be not less 
than the width of the appliance, and shall extend not less than 200mm from each side 
of the fuel loading or ash removal openings unless it forms an abutment with a wall or 
heat shield at a lesser distance. 
 
Where the floor protector consists of a number of components, it shall include a 
continuous layer of heat-resistant material extending under the appliance to the 
perimeter of the floor protector.  All joints shall be fixed to prevent accidental 
separation, and shall be sealed to prevent any spilt ash or embers contacting any heat 
sensitive material. 
 
 
 
 

Содержание Encore Urban wet












Отзывы: