Firelands X BOLT 250 Скачать руководство пользователя

Страница: 5 / 16

Locate the carbon fiber camera

mount plate and FPV camera.

Unscrew the lens from the camera

and insert through the hole on the

camera mount, rescrewing the

lens back onto the camera base.

Focusing the camera will be per-

formed after the X Bolt is assem-

bled. Focus is accomplished by

screwing the lens in/out. The lock

ring will fix the position of the cam

era to the camera mount.

Mount the camera plate to the

plastic camera mount using two

M3 6mm screws.

Note that the camera power

connection is located nearest the

frame. (See Photo)

HCT mount option

Locate the carbon fiber top plate.

Install three M3 10mm standoffs

as shown in photo to right. Locate

the two HCT plastic mount halves.

Install bottom half to the frame

using M3 6mm screw as shown in

photo at right.

Содержание X BOLT 250

















Результаты поиска

Содержание X BOLT 250

Отзывы:

Похожие инструкции для X BOLT 250

Бренды по названию

Популярные бренды

Firelands X BOLT 250, Инструкция по сборке

Результаты поиска

Содержание X BOLT 250

Отзывы:

Похожие инструкции для X BOLT 250

Бренды по названию

Популярные бренды