Firelands X BOLT 250 Скачать руководство пользователя

Страница: 1 / 16

Assembly Manual

Product specifications are subject to change without notice.

Due to ongoing development, the actual product may vary from

images shown.

This product is not a toy! (14+) Recommended for ages 14 and

up. Adult supervision required for ages under 18 years old.

Contains small parts, keep out of reach of children 3 years of

age and younger.

Distributed in the

UK by:

J Perkins Distribution Ltd,

Lenham,

Kent, UK

ME17 2DL.

www.jperkins.com

Distributed in Australia by:

Model Engines (Aust.) Pty. Ltd.,

Unit 1, 158-168 Browns Road,

Noble Park,

Victoria,

3174,

Australia.

www.modelengines.com.au

Ph (03) 8793 5555

[email protected]

Distributed in the US by:

Firelands Customer Service/Product

Support

1133 Libra Drive, Lincoln, NE 68512

www.firelandsgroup.com

1-800-205-6773

[email protected]

MADE IN CHINA

This product contains chemicals known to the State of California

to cause cancer, birth defects and other reproductive harm.

Electronics

Carbon Fiber Manufactured

and Machined in USA

X Bolt FPV Racer Kit AZSZ2903

Packaged and Assembled

in USA

Содержание X BOLT 250

















Результаты поиска

Содержание X BOLT 250

Отзывы:

Похожие инструкции для X BOLT 250

Бренды по названию

Популярные бренды

Firelands X BOLT 250, Инструкция по сборке

Результаты поиска

Содержание X BOLT 250

Отзывы:

Похожие инструкции для X BOLT 250

Бренды по названию

Популярные бренды