background image

 

 
Installing the CO Sentinel 
 

The CO Sentinel consists of three basic components: the cover, the circuit board and a 
base plate.  In addition, four screws are included, two each Phillips Head No. 6 metal 
screws and two each 6-32 machine screws.  The CO Sentinel can be mounted either to 
a flat surface or directly on to a standard electrical handi-box. 
 
The CO Sentinel comes with the circuit board installed in the base plate.  When 
installing, it may be necessary to remove the circuit board from the base plate.  To do 
this, follow the directions below.  After removing the circuit board, hold the base plate 
firmly in place and install screws. Replace the circuit board and replace the connector(s) 
on the circuit board.  Snap the cover in place and installation is complete. 
 
After installation is complete, attach one of the enclosed “Warning” stickers to the wall 
next to the alarm.  The phone numbers of emergency services and qualified technicians 
should be added to the stickers. 
 

CO Sentinel Carbon Monoxide Alarm 
 

TO REMOVE CIRCUIT BOARD FROM BASE PLATE 

 

 

 

 

FIGURE 1  

 

 

 

 

FOLLOW 

THESE 

TWO 

STEPS: 

       

 

 

1. Push “locking pins” outward and lift bottom 
portion of board toward you. 
 
2. Holding the board with one hand, pull to 
remove the connector(s). 
 
TO RE-INSTALL: Reverse this procedure. 
 
TO INSTALL CIRCUIT BOARD INTO 

BASE PLATE, FOLLOW THESE TWO 
STEPS: 

 

 

 

 

 

 

 

 

 

FIGURE 2

 

1. Insert top of board (with 45’ angles) under  
holding tabs on base plate. 
 
2. Gently lower bottom until board “snaps” 
into locking pins. 

 
 

 
 
 
 
 
 

Содержание CMD-4M















Отзывы: