Fire-Lite Alarms ES-200X Скачать руководство пользователя страница 69

Страница: 69 / 168

ES-200X Series Manual —

P/N LS10131-000FL-E:C 7/25/2018

Master Programming Level

Programming

Special Purpose Zone

Pressing

for Special Purpose, while viewing Zone Setup Screen #1, will display the following screens:

Zones 097, 098, 099, and 096 can be programmed for normal zone operation or for special purpose applications. In the above illustra-
tion, the four zones are shown Off, which means they can be programmed to function in the same manner as all other zones, by assigning
them to input and output devices in the Programming Zone Assignment Screen.

Pressing

will cause the display to change to

PAS 97 On

. Each press of the

key will cause the display to toggle between

PAS 97 On

and

PAS 97 Off

. When Zone 097 is programmed On, a PAS (Positive Alarm Sequence) activation of any smoke detector will cause Zone 097

to activate. By assigning Zone 097 to a control module in the Programming Zone Assignment Screen, an output device connected to the
control module can be used to indicate a PAS condition in the control panel.

Do not assign Zone 97 to a Notification Appliance Circuit

when using this zone to indicate a PAS condition. Attempting to do so will generate an error message and will be prevented by software
checks.

Pressing

will cause the display to change to

Pre-signal 98 On

. Each press of the

key will cause the display to toggle between

Pre-sig-

nal 98 On

and

Pre-signal 98 Off

. When Zone 098 is programmed On, a Pre-signal activation of any device will cause Zone 098 to acti-

vate. By assigning Zone 098 to a control module in the Programming Zone Assignment Screen, an output device connected to the
control module can be used to indicate a Pre-signal condition in the control panel.

Do not assign Zone 098 to a Notification Appliance

Circuit when using this zone to indicate a Pre-signal condition. Attempting to do so will generate an error message and will be prevented
by software checks.

Pressing

will cause the display to change to

Two Stage 99 On

. Each press of the

key will cause the display to toggle between

Two

Stage 99 On

and

Two Stage 99 Off

. Refer to “Two Stage Operation” on page 77 for a description of this feature.

Pressing

while viewing the Special Purpose Zone Screen #2 will cause the display to change to

Local Alm 96 On

. Each press of the

key will cause the display to toggle between

Local Alm 96 On

and

Local Alm 96 Off

. When Zone 096 is programmed On, a Local Alarm

activation of any smoke detector will cause Zone 096 to activate. By assigning Zone 096 to a control module in the Programming Zone
Assignment Screen, an output device connected to the control module can be used to indicate a local alarm condition in the control
panel.

Local Alarm Zone alarms are not reported to the Central Station.

Zones Installed

Pressing

for Zones Installed, while viewing Zone Setup Screen #2, will display a screen similar to the fol-

lowing:

This display will show all of the zones that have been programmed into the control panel. Note that an up and/or down arrow may appear
in the upper right corner of the display, indicating that additional screens of zone information exists. Press the up or down arrow keys to
view the additional zones.

Zones Enabled

Pressing

for Zones Enabled, while viewing Zone Setup Screen #2, will display a screen similar to the following:

This display will show all of the zones that are enabled in the control panel. Note that an up and/or down arrow may appear in the upper
right corner of the display, indicating that additional screens of zone information exists. Press the up or down arrow keys to view the
additional zones.

Zones Disabled

Pressing

for Zones Disabled, while viewing Zone Setup Screen #2, will display a screen similar to the following:

SPECIAL PURPOSE

1=PAS 97 OFF

2=PRESIGNAL 98 OFF

3=TWO STAGE 99 OFF

Special Purpose Zone Screen #1

SPECIAL PURPOSE

1=LOCAL ALM 96 OFF

Special Purpose Zone Screen #2

ZONE SETUP