background image

7

Chimney Types and Recommendations   

 

 

 

 

         

See Diagram on page 8.
Safety requirements demand that your Fire Chief Furnace be connected to “Class A” HT2100 All Fuel, or stainless-lined masonry 

chimney ONLY.
By definition, “Class A” refers to either a lined masonry chimney or all fuel factory-built chimney.  Although experts have expressed 

differing opinions as to which system is the best, it is a matter of what you find most suitable.  Regardless of your choice of chimney 

type, for model FC300F, a minimum 6-inch diameter chimney is needed.  In order to create the most effective draft, the chimney size 

should not exceed 12 inches, with a maximum .08 water column inches of draft.  The flue draft can be measured with the use of a draft 

gage or manometer.  If there is more than .08 water column inches of draft, it can be adjusted with the installation of a flue damper.  

The stovepipe required to connect the furnace to the chimney should be a minimum of 24 gauge black or stainless steel.  NEVER USE 

GALVANIZED PIPE.  Horizontal run should not exceed 5 feet and should have a minimum rise of 2 inches per foot.  No installation 

should have more than 2 elbows, a 45° elbow is recommended over a 90° elbow.
As a safety precaution, all pipe selections should be fastened together with a minimum of 3 sheet metal screws.  For your convenience, 

the crimped male ends of the pipe should point toward the furnace to form drip-free connections, thereby reducing the possibility of 

creosote leakage from the joints.  Installing a heat reclaimer in the pipe is not recommended because it reduces the stack temperature 

thus causing creosote formation.  Installing a manually operated cast iron damper in the stovepipe between the furnace and the 

chimney pipe is recommended.  The addition of a damper will greatly assist in regulating the fire and achieving optimum results.  Always 

install a tee with clean-out cap to the chimney outlet on the back of the furnace.  This allows for easier cleaning of the chimney system.  

Never use a 90° elbow off the back of the furnace.

When using a masonry chimney, you must line the chimney with a stainless steel liner.  The stainless steel liner will keep the chimney 

temperature hotter for better draw and significantly reduce the creosote formation in the chimney.  If using this method, a 6-inch 

stainless liner should be used for model FC300F.

WARNING- RISK OF FIRE:

 

•  Do not operate with flue draft exceeding .08 water column inches (19.9 Pa).

 

•  Do not operate with fuel loading door or ash removal drawer open.

 

•  Do not store fuel or other combustible materials within marked installation clearances.

 

•  Inspect and clean flues and chimney regularly.

DANGER: Risk of Fire and Explosion.  Do not burn garbage, gasoline, naphtha, engine oil, or other flammable liquids/inappropriate 

materials.
WARNING: 

 

•  NEVER use galvanized pipe in your chimney connection, it produces poisonous gases when subjected to extreme 

 

    temperatures.

 

•  USE only lined masonry or manufactured Class “A” HT2100 All Fuel Chimney for your furnace.

 

•  INSPECT chimney system periodically for structural integrity.

 

•  CLEAN the chimney system regularly to prevent creosote accumulation.

 

•  DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

Содержание FC300F



























Отзывы: