manualshive.com logo in svg

Finn T30 HydroSeeder MO, Руководство по эксплуатации и каталог запасных частей, Страница: 34 / 55

Поделиться
Скачать
Finn T30 HydroSeeder MO Скачать руководство пользователя страница 34

28

TROUBLESHOOTING YOUR HYDROSEEDER

®

:

Problem

Probable Causes

Suggested Solutions

VALVE:

Valve stuck

Frozen

Thaw out ice and lubricate; leave 
in discharge position during stor-
age.

Constant plugging during operation Foreign material in slurry

Drain and clean out tank; check 
storage for foreign materials.

Constant plugging during loading 
and discharging

Loading HydroSeeder® before 
tank is half full of water

Reinstruct your operator. See 
pages 12 and 13.

Incorrect loading procedure

See pages 12 and 13.

Improper operation by operator

Reinstruct your operator. Review 
OPERATOR’S MANUAL.

Clutch slipping

Readjust clutch. See manual.

Not moving valve handle far 
enough

Valve should be fully open.

Machine not being flushed out 
prior to reloading

See pages 12 and 13.

Machine not being run at correct 
RPM during loading

Reinstruct your operator. See 
pages 12 and 13.

Extension hose plugs after use

Letting water run out, leaving wood 
fiber mulch to dry out

If hose has to be uncoupled, seal 
ends, to keep water in hose and 
prevent wood fiber mulch from dry-
ing out.

CLUTCH:

Does not pull load or overheats

Out of adjustment

Readjust clutch. See manual.

Jumps out of engagement

Too loose or too tight 

Readjust clutch. See manual.

PUMP:

Excessive wear

Fertilizer with highly abrasive fillers Change fertilizer – avoid abrasive 

fillers.

Overloading machine with dry 
material

Load machine to recommended 
capacities.

Too much time allowed between 
loading and discharging

After loading and mixing has been 
completed, set agitator at 1/2 
speed in reverse and disengage 
pump.

Recirculating all the time

Close recirculation valve when dis-
charging through the boom.

Will not turn

Frozen

Warm housing to melt ice.

Jammed with fertilizer or lime

Remove cover and clean interior.

Impeller rusted to suction cover 
plate

Pull cover and remove rust.

Содержание T30 HydroSeeder MO
























































Отзывы:

Нет отзывов