Finn EAGLE 244D, Руководство по эксплуатации и каталог запасных частей

Страница: 7 / 38

3
These actions are recommended to avoid unauthor-
ized use, runaway, vandalism, theft and unexpected
operation when the equipment is restarted.
15. Do not smoke, read, eat or otherwise lose or lessen
your attention in any manner while operating the
SkidSteer. Operating is a full time job.
16. Do not carry arm in the
raised position. Always
carry loads close to the
ground. Do not step off of
the operating platform with
the load raised.
17. Check carefully for overhead clearances before
driving under them. Never contact any obstruction.
18. Stay clear of all electrical conductor lines.
19. Do not try to stabilize the machine with your hands
or feet.
20. Do not exceed a slope of 15 degrees. Avoid starting
or stopping on slopes.
21. Never carry passengers on equipment or attach-
ments. This is not a toy and should not be used
for recreation. Do NOT fool around: operate in a
smooth controlled fashion.
22. Do not exceed the rated operating capacity, as
machine may become unstable which may result in
loss of control.
23. Operate only in daylight or sufficient artificial light.
24. Use extra care when loading or unloading the
machine onto a trailer or truck. The unit should be
lifted from the lift eye located on the top center
frame member. When transporting the machine on a
truck or trailer always properly secure using straps
or chains in areas that will not damage equipment.
Chain tie-down rings are provided on each side of
machine.
25. Do not operate near drop-offs, ditches, or embank-
ments. The machine could suddenly turn over if a
wheel goes over the edge of a cliff or ditch, or if
an edge caves in.
III. MAINTENANCE:
1. Before servicing the
machine, turn off engine
and allow all moving parts
to stop. Disconnect the
battery cables to prevent
accidental starting of the
machine. Tag the engine
operating area to show that
the machine is being ser-
viced. Use lockout/tagout procedure (29 CFR
1910.147).
2. Battery maintenance. Lead-acid batteries contain
sulfuric acid which may damage eyes or skin on
contact. Always wear a face shield to avoid acid in
the eyes. If acid contacts eyes, flush immediately
with clean water and get medical attention. Wear
rubber gloves and protective clothing to keep acid
off skin. Lead-acid batteries produce flammable and
explosive gasses. Keep arcs, sparks, flames, and
lighted tobacco away.
3. Filling of fuel. Never fill the fuel tank with the
engine running, or while smoking or when near an
open flame. Never smoke while handling fuel or
working on the fuel system. The fumes in an empty
container are explosive. Never cut or weld on fuel
lines, tanks, or containers. Wipe off any spilled fuel
and let dry before starting engine.
NOTE: Be careful not to allow fuel, lubricant, hydrau-
lic fluid, or cooling fluids to penetrate into the ground
or be discharged into the water system. Collect all
used fluids and dispose of them properly.
4. It is recommended that only authorized genuine
FINN replacement parts be used on this machine.
5. Fuel or hydraulic fluid under
pressure can penetrate the
skin or eyes and cause
injury, blindness or death.
To check for such leaks,
use a piece of cardboard
or wood instead of your
hand. Pressure may build
up in the hydraulic system
so use caution when
removing the cap.
6. Perform all maintenance with the loader arms in
the lowered position. If any maintenance requires
the arms raised, secure the cylinder with locking
device.
7. Some parts and assemblies are quite heavy. Before
attempting to unfasten any heavy part or assembly,
arrange to support it by means of a hoist, by blocking
or by use of an adequate arrangement to prevent
it from falling, tipping, swinging or moving in any
manner which may damage it or injure someone.
Allow all components on machine or attachments to
cool before attempting to maintain, adjust or service,
or before storing.
8. Stop and inspect the equipment if you strike an
object. Repair if necessary.
9. If repairs require use of a torch or electric welder, be
sure that all flammable and combustible materials
are removed. Fuel or oil reservoirs must be emptied,
steam cleaned and filled with clean water before
any cutting or welding on them is attempted. Do
NOT weld or cut on any tank containing oil, gasoline
or their fumes or other flammable material, or any
container whose contents or previous contents are
unknown.