background image

Page 3 

 

Assembly Procedure (20V-25-700-ATV) 

Step 1 

Step 2 

Normally,  the  sprayer  will  be  mounted  on  an  ATV  with 

the pump assembly at the operator’s back and the spray 

wand will be at the rear of the unit. Right Hand (RH) and 

Left Hand (LH) sides of the sprayer are  

determined  as  if  you  are  standing  behind  the  sprayer, 

looking at it (facing forward) 

 

After removing the tank from the box, start the assembly 

procedure by turning the tank upside down on a stable, 

flat surface. 

 

A phillips head screwdriver is required for this step. 

 

(**) Mount tank brackets to the underside of the tank as 

shown in Step 1. Use (4) flat head screws to secure it to 

the tank. The tank will rest on the surface of the brack-

ets. Make sure the brackets are parallel with each other 

before tightening down the bolts. Do not over-tighten. 

After  your  tank  brackets  are  securely  attached,  turn 

the tank assembly over and position it so that the cam 

handles which extend beyond the back of the tank are 

facing you and just hanging over the edge of the table 

or flat surface you are assembling this on. 

 

Secure the boom mounting brackets to the tank  

mounting brackets with Cam handles as shown in  

Detail A. You can position them as needed within the 

slot  on  the  bracket.  Just  be  sure  that  the  surfaces  of 

both brackets are even with each other. 

 

You are now ready to mount this unit to an ATV, using 

ratchet straps (NOT INCLUDED) 

Detail A 

Содержание 5303076

















Отзывы: