Fimco 3PT-45-PRO-4 Скачать руководство пользователя страница 5

Страница: 5 / 14

Page 5

**The Sprayer is now ready to TEST w/plain water before actual use**

Step 4

Next, attach the center boom member of the 4-nozzle boom to

the boom mounts, centering it on the unit, using the (2) U-Bolts

and (4) 5/16”-18 Hex Whiz Nuts.

Important:

Make sure the outer boom members fold

‘backwards’.

Step 5

With the boom secured to the boom

support bars, the nozzle harness can now

be attached.

Center the nozzle harness to the boom

and using the nozzle clamps, attach the

nozzle harness to the boom.

Step 6

After your nozzle harness is attached to the boom,

attach the boom feeder hose. Place (2) hose clamps

loosely onto each end of the hose, loosely. Slip the

ends of the hose over the hose barbs on both the

manifold and the poly tee fitting on the nozzle har-

ness. Use a twisting motion, if necessary to get the

hose fully onto each barb. Bring the hose clamps to

the connection point and tighten securely.

Thread the pressure gauge into the manifold.

Hand tight should be sufficient.

Attach hose wraps, as shown.

Finally, thread the multi-lid onto the tank.

Assembly Instructions:

Содержание 3PT-45-PRO-4















Результаты поиска

Содержание 3PT-45-PRO-4

Отзывы:

Похожие инструкции для 3PT-45-PRO-4

Бренды по названию

Популярные бренды

Fimco 3PT-45-PRO-4, Руководство пользователя

Результаты поиска

Содержание 3PT-45-PRO-4

Отзывы:

Похожие инструкции для 3PT-45-PRO-4

Бренды по названию

Популярные бренды