Fimap MAXIMA BASE BT 2017, Руководство по эксплуатации и обслуживанию

Страница: 17 / 28

14. Make sure the vacuum tube (11) is correctly connected to the sleeve in the squeegee body. If it
isn't, connect it (
Fig.10
).
15. Make sure the vacuum motor filter (12) is correctly connected and is clean ( Fig.11 ). If it isn't,
clean it (see “ CLEANING THE RECOVERY TANK ”).
16. Make sure the filter basin (13) is correctly connected and is clean ( Fig.12 ). If it isn't, clean it
(see “ CLEANING THE RECOVERY TANK ”).
17. Make sure the recovery tank cover is properly closed. If it isn't, close it.
STARTING WORK
To start working, proceed as follows:
1. Make all the checks listed in “ PREPARING TO WORK ”.
2. Go to the driving position, behind the machine.
3. Turn the main switch (1) to "I", making a quarter turn of the key in the direction of the arrow
( Fig.1 ).
4. When the display comes on, the screens appear in sequence.
N.B. : In the first screen the nominal battery voltage programmed into the control board is
displayed on the left of the screen, and on the right, the minimum inhibit temperature appears
( Fig.2 ).
NB : The second screen displays the hours of work completed by the machine ( Fig.3 ).
NB
: the steps for a complete scrubbing and drying cycle are explained below.
5. Lower the brush head body and detach the "BRUSH HEAD CONTROL" pedal (2) at the rear of
the machine from the plate retainer ( Fig.4 ).
6. Lower the squeegee body and turn the squeegee control lever (3) in the direction of the arrow
( Fig.5 ). The lever is located on the back of the machine.
7. When the dead man's lever (4) is pressed, the machine will begin to move. The lever is located
underneath the control handlebars ( Fig.6 ).
NB :
the gearmotor will only begin functioning, and the solenoid valve will only begin dispensing
detergent solution, when the brush head body is in its working position.
8. During the first few metres, check that the detergent solution coming out is suitable for the task in
hand. If it isn't, adjust it after reading the section " REGULATING THE DETERGENT SOLUTION ".
The appliance will now begin to work with full efficiency until the battery is flat or until the detergent
solution has finished.
During the first few metres, check that there is sufficient solution and that the squeegee is drying
correctly.
NB : If the dead man's lever is released during the scrubbing with drying operation, the brush
motor and the solenoid valve will be deactivated. The vacuum motor will continue working until
the squeegee control lever is rotated to bring it back to its idle position.
NB : if the squeegee body is raised during the scrubbing and drying operation, the vacuum
motor will continue working at maximum speed for a certain period of time, and then switch off.
This ensures that all the liquid in the vacuum tube is eliminated.
NB : when filling the solution tank, it is good practice to empty the recovery tank using the
special drainage tube.
SCRUBBING WITH DRYING
To perform a scrubbing and drying program, proceed as follows:
1. Make all the checks listed in “ PREPARING TO WORK ”.
2. Go to the driving position, behind the machine.
3. Turn the main switch (1) to "I", making a quarter turn of the key in the direction of the arrow
( Fig.1 ).
4. Lower the brush head body and detach the "BRUSH HEAD CONTROL" pedal (2) at the rear of
the machine from the plate retainer ( Fig.2 ).
5. Lower the squeegee body and turn the squeegee control lever (3) in the direction of the arrow
( Fig.3 ). The lever is located on the back of the machine.
SCRUBBING WITHOUT DRYING
To perform a scrubbing only program, proceed as follows:
1. Make all the checks listed in “ PREPARING TO WORK ”.
2. Go to the driving position, behind the machine.
3. Turn the main switch (1) to "I", making a quarter turn of the key in the direction of the arrow
( Fig.1 ).
4. Lower the brush head body and detach the "BRUSH HEAD CONTROL" pedal (2) at the rear of
the machine from the plate retainer ( Fig.2 ).
5. When the dead man's lever (3) is pressed, the machine will begin to move. The lever is located
underneath the control handlebars ( Fig.3 ).
NB : the gearmotor will only begin functioning, and the solenoid valve will only begin dispensing
detergent solution, when the brush head body is in its working position.
DRYING
To perform a drying program, proceed as follows:
1. Make all the checks listed in “ PREPARING TO WORK ”.
2. Go to the driving position, behind the machine.
3. Turn the main switch (1) to "I", making a quarter turn of the key in the direction of the arrow
( Fig.1 ).
4. Lower the squeegee body and turn the squeegee control lever (2) in the direction of the arrow
( Fig.2 ). The lever is located on the back of the machine.
5. When the dead man's lever (3) is pressed, the machine will begin to move. The lever is located
underneath the control handlebars ( Fig.3 ).
NB : the vacuum motor will only begin to work when the squeegee body is in contact with the
floor.
6. When the dead man's lever (4) is pressed, the machine will begin to move. The lever is located
underneath the control handlebars ( Fig.4 ).
NB : the gearmotor will only begin functioning, and the solenoid valve will only begin dispensing
detergent solution, when the brush head body is in its working position.
The drying without scrubbing operation should only be
carried out if the machine was previously used to
carry out a scrubbing without drying operation.
17
1 2 3
1
11 10 12
11
12 13
4
4
1
1
2
2
3
3
5
3
4
6
4
2
1
1
2
2
3
3
1
1
2
2
3
3