manualshive.com logo in svg

Fike TWINFLEXpro, Руководство пользователя

Поделиться
Скачать
Fike TWINFLEXpro Скачать руководство пользователя страница 5

TWINFLEX

®

pro Repeater Panel Engineering and Commissioning Manual 

 
 

5 

 

Introduction 
 

This Manual is intended as a guide to the engineering and commissioning principles of the 
TWINFLEX

®

pro Repeater Panel and covers the system hardware information only. 

 
Due to the complexity and inherent importance of a system covering a ‘Life Protection Risk’, training on 
this equipment is essential and commissioning should only be carried out by competent and approved 
persons. For further details of the availability of commissioning services, please contact your supplier. 

 
System Design 

 

This document does not  cover Fire Alarm system design  and a basic understanding is 
assumed.  
 

A knowledge of BS5839: Pt 1: 2002: Fire Detection and Alarm Systems for Buildings 
is essential. 

 
It is strongly recommended that a suitably qualified and competent person is consulted in 
connection with the Fire Alarm System design and that the entire system is commissioned 
in accordance with the current national standards and specifications. 

 

Equipment Guarantee 

 

The equipment carries no warranty unless the system is installed, commissioned and 
serviced in accordance with this manual and the relevant standards by a suitably qualified 
and competent person or organisation 

 

 
 

Anti-Static Handling Guidelines 

 

Immediately prior to handling any PCBs or other static sensitive devices, it is essential to 
ensure that a personal 

connection to earth is made with an anti-static wrist-strap

  or 

similar apparatus. 
 
Always handle PCBs by their sides and avoid touching any components. PCBs should also 
be stored in a clean dry place, which is free from vibration, dust and excessive heat and is 
protected from mechanical damage. 

 

Warning 

Do not attempt to install this equipment until you have fully read and understood 
this manual. 

 
Failure to do so may result in damage to the equipment and could invalidate the warranty.  
 
For technical support please contact your distributor.  Do not call the Fike Safety 
Technology support department unless your distributor has first given their advice and 
attempted to rectify the issue. 
 
Technical  support will 

not

  be available  if the instruction manual has not been read and 

understood. Please have this instruction manual available whenever you call for technical 
support. 

! 

! 

! 

! 

Содержание TWINFLEXpro



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды