Fike ECS Series Скачать руководство пользователя | Manualshive

Страница: 43 / 66

background image

ECS Series Manual —

P/N LS10262-001FK-E:A 3/3/2021

43

Installing the FIK-125W

Device Installation

4.6.6 VBUS Wiring

The VBUS is an analog voice bus that carries the recorded voice messages from the FIK-NVCM to the FIK-125W or the voice messages
generated from a system microphone to the FIK-125W. The maximum resistance on the VBUS is 20

Ω

.

Connect the VBUS from the FIK-NVCM to the FIK-125W as shown in Figure 4.36.

Figure 4.36 VBUS Wiring for FIK-NVCM

4.6.7 SBUS Wiring

This section contains information on how to connect FIK-125Ws (up to 8 for FCP-300ECS; up to 16 for FCP-2100ECS) onto the main con-
trol SBUS. Refer to Section 4 of the FACP’s Installation manual for SBUS specifications. Wire the SBUS as shown in Figure 4.37 or
Figure 4.37 for the FIK-NVCM.

Supervised
power limited

15k

Ω

EOL

at last panel
on the VBUS

FIK-125W

FIK-125W

FIK-NVCM

«
...
41
42
43
44
45
...
»

Содержание ECS Series



































































Отзывы:

Нет отзывов

Похожие инструкции для ECS Series

Бренд: VCON Страницы: 16

Бренд: LaserBit Страницы: 69

Бренд: Panasonic Страницы: 28

Бренд: Goodmans Страницы: 22

SoundPoint Pro SE-220

Бренд: Polycom Страницы: 2

Бренд: SereneLife Страницы: 2

Бренд: Jandy Страницы: 32

Бренд: ATL Страницы: 46

Бренд: Qtx Страницы: 5

Бренд: Oakcastle Страницы: 25

Бренд: BFT Страницы: 68

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 6

Бренд: Siemens Страницы: 15

Бренд: Siemens Страницы: 7

Бренд: Siemens Страницы: 11

Бренд: Siemens Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды