Fike ECS Series Скачать руководство пользователя

Страница: 20 / 66

ECS Series Manual —

P/N LS10262-001FK-E:A 3/3/2021

Section 4: Device Installation

4.1 Connecting AC Power and Batteries

Refer to the FACP’s installation manual for proper AC power connections.

4.2 Installing the FIK-NVCM

This section provides information on the FIK-NVCM, Network Voice Control Module. The FIK-NVCM is compatible with the FCP-
2100ECS and FCP-300ECS FACPs.

For more information on how to install or remove the FIK-NVCM Network Voice Control Module, see installation sheet PN
LS10169-002FK-E.

4.2.1 FIK-NVCM Board Layout

Figure 4.1 Front View of FIK-NVCM

ECS Series Model Number

FACP Installation Manual

FCP-300ECS

LS10145-002FK-E

FCP-2100ECS

LS10143-002FK-E

Network Connector P4

Keypad connector P3

VBUS1

VBUS2

Port 1

Port 2

AUX AUDIO

CMD1

COMMON

CMD2

Fiber

Module

Connectors

Содержание ECS Series



































































Результаты поиска

Содержание ECS Series

Отзывы:

Похожие инструкции для ECS Series

Бренды по названию

Популярные бренды

Fike ECS Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание ECS Series

Отзывы:

Похожие инструкции для ECS Series

Бренды по названию

Популярные бренды