manualshive.com logo in svg

Fiery E-41, Инструкция по установке и обслуживанию

Поделиться
Скачать
Fiery E-41 Скачать руководство пользователя страница 135

T

ROUBLESHOOTING

135

Control Panel messages

Could not mount the dos/
boot partition.

When transferring options following 
installation of a new motherboard 
(

page 73

), you used the Feature Update 

CD. The E-41 does not support the 
Feature Update CD.

Obtain the Fiery Options Utility and try the procedure again.

Invalid dongle found! 
Please remove dongle and 
connect the correct 
dongle.

The attached dongle is not supported by 
the Fiery Options Utility. The dongle may 
have been attached by mistake.

Obtain a valid dongle and try again. 

Control Panel messages (cont.)

More than one dongle 
found. Remove all 
dongles except the 
correct dongle.

The Fiery Options Utility will not work 
when more than one dongle is attached to 
the system.

Remove all dongles except the correct dongle.

No uses remaining.

The dongle has already been used and 
cannot be reused.

Obtain an unused dongle and try again.

Control Panel functions

E-41 is getting power, the 
Control Panel is not black, 
but the buttons on the 
Control Panel do not 
function.

Possibly one of the following:

• Problem with the Fiery application

• Faulty User Interface Board

1. Recheck all cables and connections.

2. Reboot the E-41.

3. If the problem persists, reinstall system software

 

(see 

page 105

).

4. If the problem persists, replace the User Interface Board

 

(see

 page 58

).

DVD drive

DVD drive is not 
responding, cannot be 
located, or the disk will 

 

not eject.

Possibly one of the following:

• A disk is stuck in the DVD drive

• Cable connections to the DVD drive are 

loose or data cable is faulty

• DVD drive is faulty

• Motherboard is faulty

1. If the problem persists, check the cable connections to the 

DVD drive (see 

Figure 12 on page 48

).

2. If a disk in the DVD drive will not eject, remove the front 

panel (see 

page 51

) to access the eject button on the 

DVD drive itself. Power on the E-41 and press the eject 
button to eject the disk.

3. Check the DVD drive data cable connection to the 

motherboard.

4. If the problem persists, you may need to replace the 

DVD drive (see 

page 101

).

5. If the problem persists, you may need to replace the 

motherboard (see 

page 65

).

Symptom

Possible cause

Suggested action 

Содержание E-41


































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды