Fiery E-41 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 161

background image

S

YSTEM

AND

USER

SOFTWARE

105

S

YSTEM

AND

USER

SOFTWARE

This chapter describes how to install system and user software on the E-41 HDD. It also
details backing up and restoring Setup configuration settings (

) and updating system

and user software (

Overview

The E-41 ships with pre-installed system software on the HDD (hard disk drive). If you must
reinstall system and user software when servicing the E-41, use the latest System Software and
User Software DVDs.

N

OTE

:

You can change the default language preinstalled at the factory using the Configure

tool available through Command WorkStation and WebTools. Launch Configure and then
navigate to Server > General > Choose Server Language and then click Apply.

Before you install system software

When installing software, keep in mind the following:

•

Jobs

—All jobs in all print queues and all jobs archived locally on the E-41 HDD are

deleted when you install system and user software. To save jobs, ask the network
administrator to archive them to a CD or location on the network, so that the jobs can be
imported back into the E-41 queue after software installation. For more information, see
Command WorkStation Help.

N

OTE

:

Notify the network administrator at the customer site that some archived jobs may no

longer print after you install an updated version of system and user software.

•

Job Log

—The list of jobs in the Job Log and any jobs in the queues are deleted when you

install system and user software. The network administrator can use Command
WorkStation to save a current list of jobs (not the actual jobs) from the Job Log.

•

Fonts

—All fonts on the HDD are deleted when you install system and user

software. Resident fonts are reinstalled when you reinstall system and user software.
Any customer-supplied fonts must be reinstalled by the network administrator
using Command WorkStation.

To determine which additional fonts were downloaded to the E-41, print the Font List
before you install the software and again after you complete the software installation. Any
fonts not listed after installation must be reinstalled. For more information, see Command
WorkStation Help.

«
...
103
104
105
106
107
...
»

Содержание E-41


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E-41

Бренд: Lawler Страницы: 5

Бренд: 3M Страницы: 34

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 48

Бренд: LANGER EMV-Technik Страницы: 48

Бренд: Watts Страницы: 4

Бренд: M-system Страницы: 13

Бренд: Maximum Controls Страницы: 58

CIATControl OPC Server

Бренд: CIAT Страницы: 32

Бренд: Danfoss Страницы: 8

Infi 90 IMAOM01

Бренд: Bailey Страницы: 44

Бренд: K&K Страницы: 10

MorphoAccess VP MD

Бренд: Idemia Страницы: 29

Lux Intelligent

Бренд: Advanced Страницы: 62

Бренд: intech 21 Страницы: 15

Бренд: Xsens Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды