Fiery E-41 Скачать руководство пользователя страница 132

Страница: 132 / 161

ROUBLESHOOTING

132

Startup (cont.)

E-41 is getting power, but
the Control Panel is black.

• UIB cable is not connected to the

motherboard, the User Interface
Board, or both

• Faulty UIB cable

• Faulty User Interface Board

1. Recheck all cables and connections.

2. Use a different UIB cable.

3. If the problem persists and you have verified that the

power supply and motherboard are functioning properly as
described earlier, replace the User Interface Board (see

page 58

Following installation of a
new User Interface Board,
the Control Panel remains
blank, yet backlit, for

more than 5 minutes.

System software requires an additional
reboot to synchronize with the firmware
on the new User Interface Board.

Wait 5 minutes, power off using the power button,

wait 10 seconds, and then press the power button to

power on again.

NOT following
installation of a new User
Interface Board, system
stops responding at this
screen:

Possibly one of the following:

• Faulty BIOS

• Faulty motherboard

1. Recheck all cables and connections.

2. Reboot the E-41.

3. If the problem persists, replace the motherboard

(see

page 65

System stops responding at
this screen:

Problem with the Fiery application.

1. Recheck all cables and connections.

2. Reboot the E-41.

3. If the problem persists, reinstall system software

(see

page 105

Symptom

Possible cause

Suggested action

Activity light status:

Off.

Activity light status:

N/A.

Activity light status:

Off.

S T A R T I N G U P. . .

Activity light status:

Blinking green.

Содержание E-41


































































































































































Результаты поиска

Содержание E-41

Отзывы:

Похожие инструкции для E-41

Бренды по названию

Популярные бренды

Fiery E-41, Инструкция по установке и обслуживанию

Результаты поиска

Содержание E-41

Отзывы:

Похожие инструкции для E-41

Бренды по названию

Популярные бренды