Fiery E-41 Скачать руководство пользователя страница 103

Страница: 103 / 161

ERVICE

ROCEDURES

103

REPLACE

THE

DVD

DRIVE

1. Install the DVD drive in the switch bank assembly.

2. Install the switch bank assembly in the Component Sled, and then install the Component Sled

in the chassis (see

page 100

3. Attach the power and data combination cable to the back of the DVD drive.

Make sure that the other end of the data cable is connected to motherboard connector
SATA 1.

4. If you replaced the DVD drive with a new DVD drive, clear the CMOS as follows:

You need to clear the CMOS after installing a new DVD drive to ensure compatibility
between the new component and the previous settings stored in the BIOS. Make sure the
power cable is removed from the power outlet before clearing the CMOS.

• Remove the battery (see

page 84

• Wait 2 minutes to allow the motherboard electrical components to fully discharge.

• Reinstall the battery.

5. If you installed a new DVD drive and cleared the CMOS, make sure to reset the time and date

in Setup (see

Configuration and Setup

6. Reassemble the E-41 and verify its functionality (see

page 104

Содержание E-41


































































































































































Результаты поиска

Содержание E-41

Отзывы:

Похожие инструкции для E-41

Бренды по названию

Популярные бренды

Fiery E-41, Инструкция по установке и обслуживанию

Результаты поиска

Содержание E-41

Отзывы:

Похожие инструкции для E-41

Бренды по названию

Популярные бренды